Help with dx6
09-06-2007 | 09:50 PM
#1
Thread Starter
Senior Member
Joined: Feb 2007
Posts: 191
Likes: 0
Received 0 Likes
on
0 Posts
From: owego, NY
Help with dx6
Hi all,
I have been reading and messing with my dx6 for some time now and still dont understand theSB-trim GER and the travel adj GeR.I took off the 3in1 off of my cpp along with my g90 hh gryo and put it on my
Honey Bee fixed pitch Heli.I know about disableing the gain on the 3in1 and setting the gyro to 50%.If anyone could explain the GER setting and how they work that would be great
Thanks Rich
I have been reading and messing with my dx6 for some time now and still dont understand theSB-trim GER and the travel adj GeR.I took off the 3in1 off of my cpp along with my g90 hh gryo and put it on my
Honey Bee fixed pitch Heli.I know about disableing the gain on the 3in1 and setting the gyro to 50%.If anyone could explain the GER setting and how they work that would be great
Thanks Rich
09-07-2007 | 12:08 AM
#2
Senior Member
Joined: Oct 2006
Posts: 872
Likes: 0
Received 0 Likes
on
0 Posts
From: Savannah,
GA
RE: Help with dx6
I'm unfamiliar with the DX6, but thats probably the Gear setting you are talking about.
If your Gyro was connected to the Gear channel, you would adjust it there. Check the manual to be sure, but thats most likely it.
If your Gyro was connected to the Gear channel, you would adjust it there. Check the manual to be sure, but thats most likely it.
09-07-2007 | 12:27 AM
#3
RE: Help with dx6
Looking at my TREX settings using a telebee gyro I have the gear ch set at -45 to +45 .......one side of that is HH mode and the other is Rate mode. I know nothing about the Eflite gyros but I set mine up according to finless's vids. I also have my travel rates set at less than 100% on the rudder........ like at 75% each way. Is that any help...........or should i retreat to the corner? hers a snippit from my DX6/TREX settings:
I don't know if this will shed any light or not...... I also have some settings I picked up from the forums here for the DX6/BCP:
__________________________________________________ ___________________________________
Of all the things I ever lost....................................... I miss my mind the most!
TRV ADJ
Ger - 45% + 45% when switching to rate mode on D/R switch
PIT -100% +100% from low to high throttle
AIL -100% +100% cyclic left to cyclic right
ELE -100% +100% cyclic down to cyclic up
RUD - 75% + 74% To adjust servo travel on tail servo, it varies
Ger - 45% + 45% when switching to rate mode on D/R switch
PIT -100% +100% from low to high throttle
AIL -100% +100% cyclic left to cyclic right
ELE -100% +100% cyclic down to cyclic up
RUD - 75% + 74% To adjust servo travel on tail servo, it varies
BLADE CP PRO AND DX6
THR – Norm
AIL – Rev
ELE – Rev
RUD- Rev
GER – Norm
PIT – Norm
D/R - Dual Rates
AIO - 75%
AI1 - 100%
ELO - 75%
EL1 - 100%
EXP – Exponential
AIO – 6%
AI1 – 6%
ELO – 6%
EL1 – 6%
Sub-Trim – Will vary and will be set once the heli is powered up to center the 3 CCPM servos. This will be mentioned later in the article.
TRV ADJ
RUD – 80% in both directions
THR (-110%) at bottom stick and (+70%) at full throttle stick
All other channels should be 100% in both directions. Note default is 100% for each channel so the other channels should be at 100% at this point.
HLD – Activate Throttle Hold – See page 77 in DX6 manual.
Set 0% as value this will shut off throttle when this switch is activated.
PLN – 0% - Default Setting
P2N – 50% - Default Setting
PHN – 100% - Default Setting
PLS - 0% - Default Setting
P2S – 50% - Default Setting
PHS – 100% - Default Setting
PLH – 0% - Default Setting
P2H – 50% - Default Setting
PHH – 100% - Default Setting
TLN – 0% - Default Setting
T2N – 70%
THN – 100% - Default Setting
TLS – 0% - Default Setting
T2S – 70%
MIX RVU – Default Setting 0%
MIX RVD – Default Setting 0%
MIX A11 – Mix is OFF – Default Setting
MIX CP2 +70%
MIX CP3 +66%
MIX CP6 +50%
MIX CCP – ON
THR – Norm
AIL – Rev
ELE – Rev
RUD- Rev
GER – Norm
PIT – Norm
D/R - Dual Rates
AIO - 75%
AI1 - 100%
ELO - 75%
EL1 - 100%
EXP – Exponential
AIO – 6%
AI1 – 6%
ELO – 6%
EL1 – 6%
Sub-Trim – Will vary and will be set once the heli is powered up to center the 3 CCPM servos. This will be mentioned later in the article.
TRV ADJ
RUD – 80% in both directions
THR (-110%) at bottom stick and (+70%) at full throttle stick
All other channels should be 100% in both directions. Note default is 100% for each channel so the other channels should be at 100% at this point.
HLD – Activate Throttle Hold – See page 77 in DX6 manual.
Set 0% as value this will shut off throttle when this switch is activated.
PLN – 0% - Default Setting
P2N – 50% - Default Setting
PHN – 100% - Default Setting
PLS - 0% - Default Setting
P2S – 50% - Default Setting
PHS – 100% - Default Setting
PLH – 0% - Default Setting
P2H – 50% - Default Setting
PHH – 100% - Default Setting
TLN – 0% - Default Setting
T2N – 70%
THN – 100% - Default Setting
TLS – 0% - Default Setting
T2S – 70%
MIX RVU – Default Setting 0%
MIX RVD – Default Setting 0%
MIX A11 – Mix is OFF – Default Setting
MIX CP2 +70%
MIX CP3 +66%
MIX CP6 +50%
MIX CCP – ON
__________________________________________________ ___________________________________
Of all the things I ever lost....................................... I miss my mind the most!
09-07-2007 | 12:30 AM
#4
RE: Help with dx6
Also....here is my settings for the DX6 and the HBK2......but no HH gyro...just the stock rate one:
__________________________________________________ ___________________________________
Of all the things I ever lost....................................... I miss my mind the most!
Channels
TH- NOR
AIL- REV
ELE- NOR
RUD- REV
GER- NOR
PIT- NOR
____________________
Dual Rates
ELO- 70% EL1- 100%
AIO- 70% AI1- 100%
Expo
ELO and EL1 - 6%
AIO and AI1- 6%
_____________________
Subtrims
All at 0
_____________________
Travel Adjust
All at 100%
_____________________
Hold -1%
_____________________
Pitch Curves
PLN- 40% P2N- 59% PHN- 93%
PLS- 13% P2S- 59% PHS- 94%
PLH- 0% P2H- 50% PHH- 100%
_____________________
Throttle Curves
TLN- 0% T2N- 70% THN- 100%
TLS- 100% T2S- 70% THS factory set at 100%
_____________________
Revo Mix 0%
_____________________
Swash
CCP- ON CP2- -60% CP3- +60% CP6- -60%
TH- NOR
AIL- REV
ELE- NOR
RUD- REV
GER- NOR
PIT- NOR
____________________
Dual Rates
ELO- 70% EL1- 100%
AIO- 70% AI1- 100%
Expo
ELO and EL1 - 6%
AIO and AI1- 6%
_____________________
Subtrims
All at 0
_____________________
Travel Adjust
All at 100%
_____________________
Hold -1%
_____________________
Pitch Curves
PLN- 40% P2N- 59% PHN- 93%
PLS- 13% P2S- 59% PHS- 94%
PLH- 0% P2H- 50% PHH- 100%
_____________________
Throttle Curves
TLN- 0% T2N- 70% THN- 100%
TLS- 100% T2S- 70% THS factory set at 100%
_____________________
Revo Mix 0%
_____________________
Swash
CCP- ON CP2- -60% CP3- +60% CP6- -60%
__________________________________________________ ___________________________________
Of all the things I ever lost....................................... I miss my mind the most!
