DL-50 engine
10-19-2007, 11:10 PM
#51
RE: DL-50 engine
ORIGINAL: craigteffe
Does anyone have a canister setup on this engine and which one would you all recomend? Also where can i purchase.
Thanks
Does anyone have a canister setup on this engine and which one would you all recomend? Also where can i purchase.
Thanks
Mine is a Chip Hyde setup....Check with Chief Aircraft for availability as Chip is no longer in business....A VERY quiet setup...
Kevin
10-21-2007, 06:11 AM
#53
Senior Member
Join Date: Jan 2003
Location: MaitlandNSW, AUSTRALIA
Posts: 161
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
After reading through various posts in this and the previous thread [link=http://www.rcuniverse.com/forum/m_5532868/mpage_1/tm.htm]Let's try again DL-50 [/link] I decided to order an Engine from [link=http://www.dlenginesaustralia.com/]DL Engines Australia[/link] on Monday and received it on Tuesday. If this engine runs as good as the service that I received, I will be one happy man, for people living in Australia I can seriously recommend ordering from them.
Although I know that I have received the latest version of this engine (version 3 I think), could somebody please tell mr what all the changes are from version to version, and why were the changes were made?
Thanks
Pupmeister
Although I know that I have received the latest version of this engine (version 3 I think), could somebody please tell mr what all the changes are from version to version, and why were the changes were made?
Thanks
Pupmeister
10-21-2007, 06:38 AM
#54
My Feedback: (13)
Join Date: Nov 2002
Location: Maumelle,
AR
Posts: 655
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
The changes were .... in no particular order: An upgrade version to the ignition module, an upgrade from the original cage type engine mounts to mount of different design, and finally on the latest version, an upgrade of the case mounting tabs that are now almost twice as thick as the original. Standard standoffs are supplied instead of the cage type mount, which results in an overall reduction in weight even with the mounting tabs being increased in thickness. There may be something I left off, but this is what I can remember.
10-21-2007, 05:24 PM
#55
Senior Member
Join Date: Sep 2006
Location: Red Wing,
MN
Posts: 543
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
Just an update on my dl-50. It runs and starts very good. My camera on the other hand went dead.
No jammies today!
http://media.putfile.com/SD-model-yak-DL-50-24
No jammies today!
http://media.putfile.com/SD-model-yak-DL-50-24
10-21-2007, 07:56 PM
#58
My Feedback: (17)
Join Date: Nov 2002
Location: Goodyear, AZ
Posts: 1,427
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
I just ordered my second DL50 today. Obviously I'm very happy with the first one. In talking with Bob this afternoon, I thought it might be good to share this information.
22x8 Xoar - 7200 rpm
Elev 850'
60 degrees
Bisson wrap around muffler
22x8 Xoar - 7200 rpm
Elev 850'
60 degrees
Bisson wrap around muffler
10-21-2007, 09:12 PM
#59
Senior Member
My Feedback: (5)
Join Date: Feb 2004
Location: colorado springs,
CO
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
I love my DL 50. I recently got a great price ($425) on the the other two letter 50 that has been the standard for years and decided to see how good they really are. Cosmeticaly prettier. Pick up more substantial. It ran well but went lean when inverted (All twelve flights). All the pilots present got a goood laugh out of that. Didn't die but am going to put the DL 50 back on and sell this other high dollar engine and buy another DL. Guess I should have taken tach readings and done side by side comparison.
10-21-2007, 10:24 PM
#60
Senior Member
Join Date: Sep 2006
Location: Red Wing,
MN
Posts: 543
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
Chuck, Are you on synthetic or still breaking in? I have the same setup and I'm getting 6950 on my xoar. Same temp and altitude. I'm running 32 to 1 Lawn boy.
Also I have a J-tec pitts muffler. Not stock.
Also I have a J-tec pitts muffler. Not stock.
10-21-2007, 11:00 PM
#61
My Feedback: (17)
Join Date: Nov 2002
Location: Goodyear, AZ
Posts: 1,427
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
paul5992,
I'm running Amsoil Dominator 50:1 and only have a couple of gallons through it at the most. Also, I made an error on the muffler on the engine, and corrected my post. The muffler is a Bisson wrap around. I will be using a Bisson side mount on the second DL50.
Chuck
I'm running Amsoil Dominator 50:1 and only have a couple of gallons through it at the most. Also, I made an error on the muffler on the engine, and corrected my post. The muffler is a Bisson wrap around. I will be using a Bisson side mount on the second DL50.
Chuck
10-21-2007, 11:21 PM
#62
Senior Member
Join Date: Oct 2006
Location: Bothell,
WA
Posts: 131
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
DL170? Tell us more. Im in the process of building a 46% H9 Ultimate and after talking with DA about purchasing a DA150, they said I should wait till the DA170 comes out. More info on DL170 please.
10-22-2007, 04:26 AM
#63
Senior Member
Join Date: Jan 2005
Location: NorwichNorfolk, UNITED KINGDOM
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
ORIGINAL: craigteffe
Does anyone have a canister setup on this engine and which one would you all recomend? Also where can i purchase.
Thanks
Does anyone have a canister setup on this engine and which one would you all recomend? Also where can i purchase.
Thanks
Here is a short clip of my RCLeague YAK54 with the DL50 - great engine, just putting engine #2 in an SD-Models 30% YAK.
[link]http://uk.youtube.com/watch?v=5_dlAyYRTNk[/link]
10-22-2007, 08:49 PM
#64
Member
Join Date: Feb 2006
Location: wedowee,
AL
Posts: 95
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
Trying to start a little activity on this thread. Since it was closed and restarted their hasent been much posted. Here is my latest DL 50 mount. Choke is manual as per pull handle comming toward the front. This is held in check by a wittled down servo arm (hitec). Installed the opto remote cut off LED in the center of the servo arm (should be able to see the on light in the pictures) this is from a post by aerobob in which he installed about the same. Will provide more as the work moves along. I finally had one of the poor fitting spark plugs that were talked about on the last thread. Went to NAPA and ordered a box of 10 NGK CM-6 plugs, these are the ticket to a better fitting plug and I think I will be happier with the brand name.
10-22-2007, 09:15 PM
#65
Senior Member
Join Date: Sep 2006
Location: Red Wing,
MN
Posts: 543
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
Ed your right about the NGK plug fitting better. I bought an NGK CM-6 and it fit tight. Its not the head that is loose its the cheap sparkplug that comes with it.
10-23-2007, 06:04 AM
#68
Senior Member
Join Date: Jan 2005
Location: NorwichNorfolk, UNITED KINGDOM
Posts: 231
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
ORIGINAL: paul5992
Ed your right about the NGK plug fitting better. I bought an NGK CM-6 and it fit tight. Its not the head that is loose its the cheap sparkplug that comes with it.
Ed your right about the NGK plug fitting better. I bought an NGK CM-6 and it fit tight. Its not the head that is loose its the cheap sparkplug that comes with it.
10-23-2007, 08:51 PM
#69
My Feedback: (6)
Join Date: Sep 2004
Location: Roseville,
CA
Posts: 282
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
ORIGINAL: edward cobb
Trying to start a little activity on this thread. Since it was closed and restarted their hasent been much posted. Here is my latest DL 50 mount. Choke is manual as per pull handle comming toward the front. This is held in check by a wittled down servo arm (hitec). Installed the opto remote cut off LED in the center of the servo arm (should be able to see the on light in the pictures) this is from a post by aerobob in which he installed about the same. Will provide more as the work moves along. I finally had one of the poor fitting spark plugs that were talked about on the last thread. Went to NAPA and ordered a box of 10 NGK CM-6 plugs, these are the ticket to a better fitting plug and I think I will be happier with the brand name.
Trying to start a little activity on this thread. Since it was closed and restarted their hasent been much posted. Here is my latest DL 50 mount. Choke is manual as per pull handle comming toward the front. This is held in check by a wittled down servo arm (hitec). Installed the opto remote cut off LED in the center of the servo arm (should be able to see the on light in the pictures) this is from a post by aerobob in which he installed about the same. Will provide more as the work moves along. I finally had one of the poor fitting spark plugs that were talked about on the last thread. Went to NAPA and ordered a box of 10 NGK CM-6 plugs, these are the ticket to a better fitting plug and I think I will be happier with the brand name.
Nicw mounting job. Looks like you put some fiber glass on the engine box. Did you just do the joints or did you do the entire box. It's hard to tell from the photos.
Thanx Rich
10-23-2007, 09:26 PM
#70
Member
Join Date: Feb 2006
Location: wedowee,
AL
Posts: 95
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
took some new picture but my computer wouldn't take them. Ifiberglassed all the outside and inside corners. sanded the edges smooth and installed the aluminum angle. went back and covered the engine box inside and out with resin.
ORIGINAL: Rfabbre
Ed,
Nicw mounting job. Looks like you put some fiber glass on the engine box. Did you just do the joints or did you do the entire box. It's hard to tell from the photos.
Thanx Rich
ORIGINAL: edward cobb
Trying to start a little activity on this thread. Since it was closed and restarted their hasent been much posted. Here is my latest DL 50 mount. Choke is manual as per pull handle comming toward the front. This is held in check by a wittled down servo arm (hitec). Installed the opto remote cut off LED in the center of the servo arm (should be able to see the on light in the pictures) this is from a post by aerobob in which he installed about the same. Will provide more as the work moves along. I finally had one of the poor fitting spark plugs that were talked about on the last thread. Went to NAPA and ordered a box of 10 NGK CM-6 plugs, these are the ticket to a better fitting plug and I think I will be happier with the brand name.
Trying to start a little activity on this thread. Since it was closed and restarted their hasent been much posted. Here is my latest DL 50 mount. Choke is manual as per pull handle comming toward the front. This is held in check by a wittled down servo arm (hitec). Installed the opto remote cut off LED in the center of the servo arm (should be able to see the on light in the pictures) this is from a post by aerobob in which he installed about the same. Will provide more as the work moves along. I finally had one of the poor fitting spark plugs that were talked about on the last thread. Went to NAPA and ordered a box of 10 NGK CM-6 plugs, these are the ticket to a better fitting plug and I think I will be happier with the brand name.
Nicw mounting job. Looks like you put some fiber glass on the engine box. Did you just do the joints or did you do the entire box. It's hard to tell from the photos.
Thanx Rich
10-24-2007, 12:21 AM
#71
My Feedback: (6)
Join Date: Sep 2004
Location: Roseville,
CA
Posts: 282
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
ORIGINAL: edward cobb
took some new picture but my computer wouldn't take them. Ifiberglassed all the outside and inside corners. sanded the edges smooth and installed the aluminum angle. went back and covered the engine box inside and out with resin.
took some new picture but my computer wouldn't take them. Ifiberglassed all the outside and inside corners. sanded the edges smooth and installed the aluminum angle. went back and covered the engine box inside and out with resin.
ORIGINAL: Rfabbre
Ed,
Nicw mounting job. Looks like you put some fiber glass on the engine box. Did you just do the joints or did you do the entire box. It's hard to tell from the photos.
Thanx Rich
ORIGINAL: edward cobb
Trying to start a little activity on this thread. Since it was closed and restarted their hasent been much posted. Here is my latest DL 50 mount. Choke is manual as per pull handle comming toward the front. This is held in check by a wittled down servo arm (hitec). Installed the opto remote cut off LED in the center of the servo arm (should be able to see the on light in the pictures) this is from a post by aerobob in which he installed about the same. Will provide more as the work moves along. I finally had one of the poor fitting spark plugs that were talked about on the last thread. Went to NAPA and ordered a box of 10 NGK CM-6 plugs, these are the ticket to a better fitting plug and I think I will be happier with the brand name.
Trying to start a little activity on this thread. Since it was closed and restarted their hasent been much posted. Here is my latest DL 50 mount. Choke is manual as per pull handle comming toward the front. This is held in check by a wittled down servo arm (hitec). Installed the opto remote cut off LED in the center of the servo arm (should be able to see the on light in the pictures) this is from a post by aerobob in which he installed about the same. Will provide more as the work moves along. I finally had one of the poor fitting spark plugs that were talked about on the last thread. Went to NAPA and ordered a box of 10 NGK CM-6 plugs, these are the ticket to a better fitting plug and I think I will be happier with the brand name.
Nicw mounting job. Looks like you put some fiber glass on the engine box. Did you just do the joints or did you do the entire box. It's hard to tell from the photos.
Thanx Rich
10-24-2007, 03:33 PM
#74
Join Date: Jan 2006
Location: Kalona,
IA
Posts: 2,517
Likes: 0
Received 0 Likes
on
0 Posts
RE: DL-50 engine
He's answered multiple emails from me...but if he's busy getting engines ready to ship, maybe you should call him? Either way he has always responded. Good guy, never in a hurry to get off the phone.
