|
Originally Posted by Dansy
(Post 12408869)
Sorry, the G2 which I think is what we are talking about doesn’t used the Xicoy ecu.....its the KingTech ECU and KingTech Telemetry device, which is different....but this might still work, I’m gone try something.
|
Originally Posted by dccatl
(Post 12408872)
My bad, didn't notice this was about the Kingtech (G2) telemetry.
|
Originally Posted by ZivBit
(Post 12388620)
Yes I did choose the JC sensor option, and it works, partially.
There is a sensor from the pump with fuel remaining. You must config the tank capacity in the KT dashboard to get a read. However, I am still not getting any RPM reading. Ziv |
I'm also looking to know how to setup my Futaba 18MZ to the telemetry module? Has anyone got it to work?
|
Cab I use the Kingtech telemetry unit with a DX20 and PowerSafe receiver? If so, how do I set that up and what will it tell me?
Thanks! |
Yes, and a bunch of info, that you can log to the SD card
|
And it will work with the latest version of the 20 channels? Does it go in the XBus? |
Originally Posted by kelly vallee
(Post 12450733)
I'm also looking to know how to setup my Futaba 18MZ to the telemetry module? Has anyone got it to work?
JanR |
Did you go into the telemtry module setup screen and select Futaba ?
for Spektrum just use the xbus...see my previous posts for spektrum... |
Originally Posted by aaronforth
(Post 12456075)
Did you go into the telemtry module setup screen and select Futaba ?
for Spektrum just use the xbus...see my previous posts for spektrum... |
If anyone is interested, there is information over on RCGroups in the Turbine forum, about new stuff from Vspeak for the KingTech ECU's.
https://www.rcgroups.com/forums/show...er-from-VSpeak |
Originally Posted by Zeeb
(Post 12456446)
If anyone is interested, there is information over on RCGroups in the Turbine forum, about new stuff from Vspeak for the KingTech ECU's.
|
Hi, anyone running a Jeti ds24 with the KT telemetry module?? I'm caine of new on Jeti so any hints will be welcome, I will install it tomorrow to my 260...
Thxs in advance |
Originally Posted by skymaster68
(Post 12471981)
Hi, anyone running a Jeti ds24 with the KT telemetry module?? I'm caine of new on Jeti so any hints will be welcome, I will install it tomorrow to my 260...
Thxs in advance You can also use the tool by Thomas on Github https://github.com/thomasekdahlN/jeti |
Hi all,
I thought I read somewhere in the KT forums that it’s advisable to connect a single cable from Jeti CB200 into the KT ECU (one of the Aux ports) as an added power backup. Is my memory correct, can anyone help ? thanks, Leon |
Leon
RCG has a big Jeti thread on the radio section, post your question there as it is supported by Esprit, Jeti USA. https://www.rcgroups.com/jeti-usa-794/ Good luck. |
Yes I always run a second lead to the AUX port on ECU as a power backup....
|
Originally Posted by Mi-25
(Post 12620115)
Hi all,
I thought I read somewhere in the KT forums that it’s advisable to connect a single cable from Jeti CB200 into the KT ECU (one of the Aux ports) as an added power backup. Is my memory correct, can anyone help ? thanks, Leon |
Originally Posted by Dansy
(Post 12620125)
I never do and I never had any flame out....
That connection is actually cover in the later G2 ECU ;) .....it’s for the Engine repair man... And the AUX port is there right up to the G4 series |
Originally Posted by aaronforth
(Post 12620127)
Lol that's like saying I dont have Insurance but it's ok I haven't been an an accident lol
And the AUX port is there right up to the G4 series PS; I’m not prone to accident ;) |
Originally Posted by Dansy
(Post 12620128)
Well I don’t used it and will never do......it’s not required, and yes it’s there....
PS; I’m not prone to accident ;) I knew somebody that had a flame out due to a poor contact on the throttle cable. A second lead would have prevented this.... |
Originally Posted by aaronforth
(Post 12620132)
your right it's not required...running duel batteries are not required either....
I knew somebody that had a flame out due to a poor contact on the throttle cable. A second lead would have prevented this.... |
Originally Posted by Dansy
(Post 12620134)
Do as you wish...... LOL 😂
|
Originally Posted by aaronforth
(Post 12620135)
thanks for the permission 🤣
|
Play nice now.
|
| All times are GMT -8. The time now is 03:51 PM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.