RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: lyotchik
Showing results 1 to 12 of 12
Search took 0.58 seconds.
Forum: Tips & Techniques
10-22-2008, 09:44 PM
Replies: 11
Views: 1,966
Posted By lyotchik

RE: ADJUSTING LEAD WEIGHTS

Thanks Everyone,
Each of the suggestions is good and I appreciate the input. Just a couple of other points. My trainer, a NexStar, required around 3 oz of lead. I've also built 2 Sig 4 Stars and...
Forum: Tips & Techniques
10-22-2008, 02:14 PM
Replies: 11
Views: 1,966
Posted By lyotchik

ADJUSTING LEAD WEIGHTS

When I built my Sig 4 Star 60, I balanced the airplane to the recommended location by using epoxy to attach lead weights to the cheeks on both sides of the engine. After reading several articles on...
Forum: Glow Engines
09-24-2008, 09:12 PM
Replies: 863
Views: 87,119
Posted By lyotchik

RE: ST2300 Testing and Experimenting

Hello guys,
As a new owner of the ST 2300, not yet out of the box, I've stumbled on this thread and have just finished reading it in full. Being an engineer, I wondered what kind of throat...
Forum: 3D Flying!
03-30-2008, 03:13 PM
Replies: 149
Views: 23,895
Posted By lyotchik

RE: Magic Hand 73" yak build thread

I'm also looking at purchasing this plane so I'm following your build with considerable interest. I would like to ask about your choice of servos. I noticed that you chose a lower torque, faster...
Forum: JR Radio & Spektrum Radios
10-18-2007, 02:33 PM
Replies: 2
Views: 780
Posted By lyotchik

DUAL RECIEVERS

I'm wondering if it might be possible to operate dual receivers. In particular, for a 1/4 or 1/3 scale biplane, could an additional receiver and battery pack be run in the upper wing so as to avoid...
Forum: Kit Building
10-18-2007, 07:40 AM
Replies: 3
Views: 1,717
Posted By lyotchik

RE: Lanier Ultimate Pitts Biplane

I hope that someone will comment on this kit. Are the instructions clear, does it use good quality balsa, is it laser or die cut, how do the cut parts fit, etc. It seems to come with an ABS cowl -...
Forum: ARF or RTF
04-28-2007, 08:24 AM
Replies: 1,604
Views: 282,713
Posted By lyotchik

RE: Seagull Yak?

:D
Forum: Kit Building
03-01-2006, 03:30 PM
Replies: 3
Views: 612
Posted By lyotchik

RE: building 4* 40 wing questions...

The 4* wing is supposed to have 2 degrees of dihedral on each panel. The "tool" provided with the kit is supposed to give you this. Each point along the length of the center rib, both sides, should...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
11-05-2005, 04:34 PM
Replies: 0
Views: 453
Posted By lyotchik

Hitec Micro 555 with Futaba 7 CAP

I have a Hitec Micro 555 that I took from an electric powered plane and would like to use in a new build of a Balsa USA Phaeton II (40 sized glow). I plan to use the Hitec HS 81 for the throttle,...
Forum: The Clubhouse
10-14-2005, 04:37 PM
Replies: 1,857
Views: 249,402
Posted By lyotchik

RE: Has RCM folded?

I had posted a message on September 29 that RCM had sent me a message stating that the plan service was still operating. I had sent in an order on that day and told everyone that I would post...
Forum: The Clubhouse
09-28-2005, 06:31 PM
Replies: 1,857
Views: 249,402
Posted By lyotchik

RE: Has RCM folded?

I had really been wanting some of the old plans and decided to go ahead, take a chance and try to order them anyway. The order went in two days ago. Today (wednesday, 28 Sep) I received the...
Forum: Beginners
04-02-2005, 08:57 AM
Replies: 24
Views: 4,998
Posted By lyotchik

RE: thoughts on the nexstar

I've been flying a NexStar about twice a week for 6 months now. It appears to be very well constructed, using good materials and clearly there is a lot of thought that went into the design. ...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.