Central NEW YORK boaters
#2826
Senior Member
Join Date: Sep 2008
Location: Rochester,
NY
Posts: 414
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
That YouTube vid that Neil gave us of the FE Cat (100mph??) looks like FE might 'RULE'!!! I'll stick with the 'gassers' for the big stuff. $4-6 per gallon (with oil) vs $40 per gallon for 50% nitro!! BTW...all the rigger talk on here got me to reassemble my Cajun Bullet Gas Rigger. One repaired sponson tip and straightened boom tubes and she's ready for action come Spring. RC
#2827
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: engineman351
That YouTube vid that Neil gave us of the FE Cat (100mph??) looks like FE might 'RULE'!!! I'll stick with the 'gassers' for the big stuff. $4-6 per gallon (with oil) vs $40 per gallon for 50% nitro!! BTW...all the rigger talk on here got me to reassemble my Cajun Bullet Gas Rigger. One repaired sponson tip and straightened boom tubes and she's ready for action come Spring. RC
That YouTube vid that Neil gave us of the FE Cat (100mph??) looks like FE might 'RULE'!!! I'll stick with the 'gassers' for the big stuff. $4-6 per gallon (with oil) vs $40 per gallon for 50% nitro!! BTW...all the rigger talk on here got me to reassemble my Cajun Bullet Gas Rigger. One repaired sponson tip and straightened boom tubes and she's ready for action come Spring. RC
$29 per gallon for 50% if I can pick it up in Florida....
#2829
Senior Member
Join Date: Aug 2006
Location: Factoryville,
PA
Posts: 268
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: advanced builder
Roger did you notice that FE only goes in a straight line. No turning.
Roger did you notice that FE only goes in a straight line. No turning.
#2830
Senior Member
RE: Central NEW YORK boaters
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self#2... Left hand needs to hold ca bottle LIGHTLY....
I just had to cut fingers free from thunderboat because of clumsy left handed ca gluing... Had to carry boat attached to hand to get x-acto blade to remove fingers... Lol... I guess this will be toms hydro... Lol.. Left some DNA for future proof of build..moving on to outer chine strips now!!!
#2831
Senior Member
Join Date: Aug 2006
Location: Factoryville,
PA
Posts: 268
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: rickyak55
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self#2... Left hand needs to hold ca bottle LIGHTLY....
I just had to cut fingers free from thunderboat because of clumsy left handed ca gluing... Had to carry boat attached to hand to get x-acto blade to remove fingers... Lol... I guess this will be toms hydro... Lol.. Left some DNA for future proof of build..moving on to outer chine strips now!!!
#2832
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
FE boats can turn, but it's a bit more difficult compared to nitro as the boats are heavier. Same issue with gas boats. Getting a light .21 rigger around a 35 foot radius doing 70 mph is a piece of cake.
I know what Neil is talking about. A lot of FE boats on Youtube can't turn with a damn. Or the driver is just too scared and has to slow down.
Scott Parker should start digging this weekend. Hopefully all goes well....
I know what Neil is talking about. A lot of FE boats on Youtube can't turn with a damn. Or the driver is just too scared and has to slow down.
Scott Parker should start digging this weekend. Hopefully all goes well....
#2833
Senior Member
RE: Central NEW YORK boaters
ORIGINAL: rickyak55
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self#2... Left hand needs to hold ca bottle LIGHTLY....
I just had to cut fingers free from thunderboat because of clumsy left handed ca gluing... Had to carry boat attached to hand to get x-acto blade to remove fingers... Lol... I guess this will be toms hydro... Lol.. Left some DNA for future proof of build..moving on to outer chine strips now!!!
Hey bob, tom had collett on his lower end, all set, thanks for the call!!
Rick P.
#2834
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: rickyak55
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self#2... Left hand needs to hold ca bottle LIGHTLY....
I just had to cut fingers free from thunderboat because of clumsy left handed ca gluing... Had to carry boat attached to hand to get x-acto blade to remove fingers... Lol... I guess this will be toms hydro... Lol.. Left some DNA for future proof of build..moving on to outer chine strips now!!!
#2835
Senior Member
RE: Central NEW YORK boaters
ORIGINAL: Billk44
FYI - they a release agent that works great. Always keep in the area when using CA.
ORIGINAL: rickyak55
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self#2... Left hand needs to hold ca bottle LIGHTLY....
I just had to cut fingers free from thunderboat because of clumsy left handed ca gluing... Had to carry boat attached to hand to get x-acto blade to remove fingers... Lol... I guess this will be toms hydro... Lol.. Left some DNA for future proof of build..moving on to outer chine strips now!!!
#2836
Senior Member
RE: Central NEW YORK boaters
ORIGINAL: Blackout
Too funny. Well you know the glue is working.
ORIGINAL: rickyak55
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self#2... Left hand needs to hold ca bottle LIGHTLY....
I just had to cut fingers free from thunderboat because of clumsy left handed ca gluing... Had to carry boat attached to hand to get x-acto blade to remove fingers... Lol... I guess this will be toms hydro... Lol.. Left some DNA for future proof of build..moving on to outer chine strips now!!!
#2837
Senior Member
Join Date: Sep 2008
Location: Rochester,
NY
Posts: 414
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
It is funny that in most YouTube FE vids the turns are very slow. Maybe the drivers are just being careful not to flip them...but I'm pretty sure that if the CG is right and the hardware is up to the task they should rip around the corners as well as any properly set up hull. We need to put the pressure on klinker19. He has a JAE21 with 4082 power on 5 cells that should provide some excitement. I think he's worried that it has so much battery and motor that if it isn't planing...it will only 'bob' straight up and down!!! RC
#2838
Thread Starter
Join Date: Feb 2006
Location: Baldwinsville,
NY
Posts: 3,055
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
I did recall how Randall expensive boat sank. Then poped up during a heat race. Big money lost. I've seen the cost of the Neu motors.
#2839
Junior Member
Join Date: Dec 2011
Location: Walworth,
NY
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: rickyak55
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self: thin ca is runny and fast, allways have knife within reach to cut fingers off whatever you are working on...
Note to self#2... Left hand needs to hold ca bottle LIGHTLY....
I just had to cut fingers free from thunderboat because of clumsy left handed ca gluing... Had to carry boat attached to hand to get x-acto blade to remove fingers... Lol... I guess this will be toms hydro... Lol.. Left some DNA for future proof of build..moving on to outer chine strips now!!!
Thanks for removing the excess fingertip. Really trying to watch the weight on this build...
TC
#2840
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: engineman351
It is funny that in most YouTube FE vids the turns are very slow. Maybe the drivers are just being careful not to flip them...but I'm pretty sure that if the CG is right and the hardware is up to the task they should rip around the corners as well as any properly set up hull. We need to put the pressure on klinker19. He has a JAE21 with 4082 power on 5 cells that should provide some excitement. I think he's worried that it has so much battery and motor that if it isn't planing...it will only 'bob' straight up and down!!! RC
It is funny that in most YouTube FE vids the turns are very slow. Maybe the drivers are just being careful not to flip them...but I'm pretty sure that if the CG is right and the hardware is up to the task they should rip around the corners as well as any properly set up hull. We need to put the pressure on klinker19. He has a JAE21 with 4082 power on 5 cells that should provide some excitement. I think he's worried that it has so much battery and motor that if it isn't planing...it will only 'bob' straight up and down!!! RC
#2841
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
Speaking of electric. Dan Hutchinson is selling a complete electric outboard setup on IW. I'd link, but that's against RCU rules. If I was to do electric, it would be an outboard JAE Zippkit rigger or tunnel.
#2842
RE: Central NEW YORK boaters
Anyone get hurt by Sandy? The wife and I have been sort of trapped in the Boston area since last night and were delayed in Washington DC due to mechanical problems with our plane flying in on the 22nd. This has made coming up and using Neil's extra shovel impossible this trip
#2843
Senior Member
RE: Central NEW YORK boaters
12:51.... Am.. Bottom on!!! Non trip sponson sides sanded and ready to sheet... Motor mounts were a b*+¥#.... But like sandy i didnt give up!!! Its looking like a thunderboat now.. Next boat#2 bottom glue up... This one should be easier... If i found a bit more of my bench, i could do 2 at same time, maby i should open both doors and let sandy do her work in here.. Needs a good cleaning... I am afraid i am not going to out last her tonight.. Kids will be home from school tomorrow( today) and i will have to stay home. Guess i will have alot of time on "project hydro"!!!!
Rick
#2846
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
Sandy made her way into my hobby room (basement). [] This is normal for any large amounts of rain....
Thanks for the concerns. We are inland enough, not so much on the coast. NYC got hit hard!
Rick, you are a building machine!
Thanks for the concerns. We are inland enough, not so much on the coast. NYC got hit hard!
Rick, you are a building machine!
#2849
Member
Join Date: Oct 2008
Location: Webster, NY
Posts: 58
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
Power is back on in webster {at my house anyway}
Craig I have a couple of guys that are interested in joining the club that run the Aquacraft UL-1's or have that set up in Dumas 36".40 size hydros.
I think it is know as the P-1 stock or spec set up in IMPBA, there are a bunch of these locally running at road side ponds..would be nice to get them into the club and racing.
I will be needing to buy some fuel for next year,please keep me in mind if you find a deal
Craig I have a couple of guys that are interested in joining the club that run the Aquacraft UL-1's or have that set up in Dumas 36".40 size hydros.
I think it is know as the P-1 stock or spec set up in IMPBA, there are a bunch of these locally running at road side ponds..would be nice to get them into the club and racing.
I will be needing to buy some fuel for next year,please keep me in mind if you find a deal
#2850
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: bdog1
Power is back on in webster {at my house anyway}
Craig I have a couple of guys that are interested in joining the club that run the Aquacraft UL-1's or have that set up in Dumas 36''.40 size hydros.
I think it is know as the P-1 stock or spec set up in IMPBA, there are a bunch of these locally running at road side ponds..would be nice to get them into the club and racing.
I will be needing to buy some fuel for next year,please keep me in mind if you find a deal
Power is back on in webster {at my house anyway}
Craig I have a couple of guys that are interested in joining the club that run the Aquacraft UL-1's or have that set up in Dumas 36''.40 size hydros.
I think it is know as the P-1 stock or spec set up in IMPBA, there are a bunch of these locally running at road side ponds..would be nice to get them into the club and racing.
I will be needing to buy some fuel for next year,please keep me in mind if you find a deal
Sounds good, the more the merrier!
I'll post on here if we do a Stony Pond fuel buy. It will be a few months still.
I'll need to get up to speed on the electric classes. The Kendalls run UL-1's in Elmira, so it could be a good class next year. We will wait and see what people bring to the pond in the spring.