RC Surfer
#4926
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
RC Surfer Wreck at "Shipwrecks" Today
Went back at 11:30.
Surfed 3 packs on the low tide.
It was sick.
Hit the reef heading out on the left side.
Jumped a wave and heard a loud thud.
Board stopped out at the peak.
Had to grab my board for a rescue.
All I could think about was all the shark stories especially that one today.
Got the guy about 50m out.
Paddled in and cut my finger on the reef about 30 feet off shore, it is like razor.
One of the brass water ports is bent over at the tip and the prop and shaft is gone.
Not a problem have more spares.
Photos from this morning have just arrived.
JIMI
Went back at 11:30.
Surfed 3 packs on the low tide.
It was sick.
Hit the reef heading out on the left side.
Jumped a wave and heard a loud thud.
Board stopped out at the peak.
Had to grab my board for a rescue.
All I could think about was all the shark stories especially that one today.
Got the guy about 50m out.
Paddled in and cut my finger on the reef about 30 feet off shore, it is like razor.
One of the brass water ports is bent over at the tip and the prop and shaft is gone.
Not a problem have more spares.
Photos from this morning have just arrived.
JIMI
#4927
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Hey Guys,
Here are a few pics from our new spot "Shipwrecks" this morning.
It was onlysmall and inconsistantbut still heaps of fun, can't wait to get it on a bigger swell.
The tide was high and it was not really happening until later on but we were very lucky to get any shots at all today.
Photos - Bob Fawcett
JIMI Findrix
Geraldton W. A.
Here are a few pics from our new spot "Shipwrecks" this morning.
It was onlysmall and inconsistantbut still heaps of fun, can't wait to get it on a bigger swell.
The tide was high and it was not really happening until later on but we were very lucky to get any shots at all today.
Photos - Bob Fawcett
JIMI Findrix
Geraldton W. A.
#4928
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Oi Wilfrad & Crew,
Had to strip and clean the board after todays encounter with the suckrock on the left side of the "Shipwrecks" peak.
All fixed and lubed up and in the car ready to go again in the morning.
Bigger surf tomorrow and building for the next 3 days.
Yeeeeeeeeoooooooooooowwwwwwwwwwwwwwwwwwww!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
5 peope killed by Whitey over here this year and numerous other encounters.
JIMI
#4930
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Hey JIMI
Great pics - the last picture really spells it out - A- W- E -S -O -M -E - SPOT.
The more I read and hear about these Great white attacks - the more appealing rc surfing becomes................ it would be something to capture a Great White 'breaching' as it takes out my Bro'Surfer on film.........................no doubt the footage would go Viral........
Enjoy the surf tomorrow - I'm hoping the wind will swing around and drop off...............................
Dominic ( Bro'Surfer)
Great pics - the last picture really spells it out - A- W- E -S -O -M -E - SPOT.
The more I read and hear about these Great white attacks - the more appealing rc surfing becomes................ it would be something to capture a Great White 'breaching' as it takes out my Bro'Surfer on film.........................no doubt the footage would go Viral........
Enjoy the surf tomorrow - I'm hoping the wind will swing around and drop off...............................
Dominic ( Bro'Surfer)
#4931
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Dom,
You are right.
The last pic gives a clue to the type of spot this really is.
No white water to contend with when heading out.
The left you can just see is even better than the right.
There is a really shallow suckrock halfway along the left, so you take off at the peak and race down the line, after the first turn you see it starting to dredge out on the rock just down the line a bit.
Then you just race into the suck out section and the bottom just drops right out of it (the board actually drops someimes) and you duck through for a quick barrel section.
That is where I hit the reef yesterday.
Jumped a wave racing out for a set and it landed right where the rock was dredging because there was a bigger wave right behind the one I jumped.
Going there again in an hour or so and it should be a bit bigger today.
JIMI
You are right.
The last pic gives a clue to the type of spot this really is.
No white water to contend with when heading out.
The left you can just see is even better than the right.
There is a really shallow suckrock halfway along the left, so you take off at the peak and race down the line, after the first turn you see it starting to dredge out on the rock just down the line a bit.
Then you just race into the suck out section and the bottom just drops right out of it (the board actually drops someimes) and you duck through for a quick barrel section.
That is where I hit the reef yesterday.
Jumped a wave racing out for a set and it landed right where the rock was dredging because there was a bigger wave right behind the one I jumped.
Going there again in an hour or so and it should be a bit bigger today.
JIMI
#4934
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Hey Dudettes,
Surf looked crap today, big swell but wind and tide are not right.
Dude undergoing surgery.
Knee and foot reconstruction.
He has taken a real beating over the last month.
JIMI
#4935
Join Date: May 2009
Location: Cape Towm, SOUTH AFRICA
Posts: 2,769
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Hi Guys !
Some R&D results from my current Board #4 build....
Oh @#$%............... that's not working........................LOL
With poor weather over the weekend ( no surfing) I got a chance to fit all the running gear into the board for a prelim test !
A definite NO GO................................ thats development for you....
The problem - - due to the prop been positioned to act as a 'surface drive prop' - the rotational torque is increased dramatically - ( not running any torque trim tabs)
Running straight and turning right is no problem
BUT ! - the moment I turn LEFT - due to the increased torque rotation acting on the V hull - the hull rolls over to the right - the hull rolls over so much so, that the rail becomes submerged and as I accelerate in the turn, the board is driven completely under water.........becomes a submarine.........!
So ! Back to plan B...........Still running the V hull - but - with a submerged prop set up - aft cut away that facilitated the Surface drive prop filled in.
Deduction ?.................No more surface drives then.............................
Regards
Dominic (Bro'Surfer)
Some R&D results from my current Board #4 build....
Oh @#$%............... that's not working........................LOL
With poor weather over the weekend ( no surfing) I got a chance to fit all the running gear into the board for a prelim test !
A definite NO GO................................ thats development for you....
The problem - - due to the prop been positioned to act as a 'surface drive prop' - the rotational torque is increased dramatically - ( not running any torque trim tabs)
Running straight and turning right is no problem
BUT ! - the moment I turn LEFT - due to the increased torque rotation acting on the V hull - the hull rolls over to the right - the hull rolls over so much so, that the rail becomes submerged and as I accelerate in the turn, the board is driven completely under water.........becomes a submarine.........!
So ! Back to plan B...........Still running the V hull - but - with a submerged prop set up - aft cut away that facilitated the Surface drive prop filled in.
Deduction ?.................No more surface drives then.............................
Regards
Dominic (Bro'Surfer)
#4936
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Alright Crew,
Dude is all fixed and has a new wetsuit.
He has been surfing with a snapped knee and totally blown out inside rear foot for ages.
Dom,
Worth a try Dude.
JIMI
#4937
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Jimi's Surf Report
4 to 6 foot swell and offshore in Gero.
Luke and I surferd 1 to 2 foot "St Georges" early on the high tide.
Ran 4 packs and got heaps of fun lefts.
Went home for an hour and then we went and surfed sick reef to beach rights at "Medalia" for an hour and a half.
Lukes Dude's foot is splattered.
JIMI
4 to 6 foot swell and offshore in Gero.
Luke and I surferd 1 to 2 foot "St Georges" early on the high tide.
Ran 4 packs and got heaps of fun lefts.
Went home for an hour and then we went and surfed sick reef to beach rights at "Medalia" for an hour and a half.
Lukes Dude's foot is splattered.
JIMI
#4938
Senior Member
Join Date: Dec 2010
Location: melbourne, AUSTRALIA
Posts: 745
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
ORIGINAL: YPC
Hi Guys !
Some R&D results from my current Board #4 build....
Oh @#$%............... that's not working........................LOL
With poor weather over the weekend ( no surfing) I got a chance to fit all the running gear into the board for a prelim test !
A definite NO GO................................ thats development for you....
The problem - - due to the prop been positioned to act as a 'surface drive prop' - the rotational torque is increased dramatically - ( not running any torque trim tabs)
Running straight and turning right is no problem
BUT ! - the moment I turn LEFT - due to the increased torque rotation acting on the V hull - the hull rolls over to the right - the hull rolls over so much so, that the rail becomes submerged and as I accelerate in the turn, the board is driven completely under water.........becomes a submarine.........!
So ! Back to plan B...........Still running the V hull - but - with a submerged prop set up - aft cut away that facilitated the Surface drive prop filled in.
Deduction ?.................No more surface drives then.............................
Regards
Dominic (Bro'Surfer)
Hi Guys !
Some R&D results from my current Board #4 build....
Oh @#$%............... that's not working........................LOL
With poor weather over the weekend ( no surfing) I got a chance to fit all the running gear into the board for a prelim test !
A definite NO GO................................ thats development for you....
The problem - - due to the prop been positioned to act as a 'surface drive prop' - the rotational torque is increased dramatically - ( not running any torque trim tabs)
Running straight and turning right is no problem
BUT ! - the moment I turn LEFT - due to the increased torque rotation acting on the V hull - the hull rolls over to the right - the hull rolls over so much so, that the rail becomes submerged and as I accelerate in the turn, the board is driven completely under water.........becomes a submarine.........!
So ! Back to plan B...........Still running the V hull - but - with a submerged prop set up - aft cut away that facilitated the Surface drive prop filled in.
Deduction ?.................No more surface drives then.............................
Regards
Dominic (Bro'Surfer)
Have you got any of my messages???
#4939
Senior Member
Join Date: Feb 2011
Location: West Melbourne,
FL
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
This thead really needs a 1st post edit or FAQs and links like other products, but I'm sure the OP probably has a life. I did try searching for vendor links for models and didn't come up with much, except for the high-buck surfers, but if you're looking for a cheap knock-off to upgrade, Banggood carries a version for 66 bucks shipped:
http://www.banggood.com/Wholesale-No...0487522012019E
Apparently made by NQD:
http://toyzcastle.com/eBay.co.uk/pro...20RC%20Surfer/
#4940
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
MasiveOverkill,
Thanks Dude, 3 boardsfor under $200 delivered is a bargain.
People are charging over $230 a board on ebay lately
JIMI
Thanks Dude, 3 boardsfor under $200 delivered is a bargain.
People are charging over $230 a board on ebay lately
JIMI
#4941
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Hey Crew,
You should have seen it today.
4 to 6 foot perfection on the Batavia coast.
"Shippies" was 2 to 3 foot and breaking on reef just barely under the surface.
Just ought 3 white NQD's for $197.95,
If I keep surfing at "Shipwrecks" I am gonna need 'em.
Surfed there today, it was sick.
Biggest, cleanest, most consistent and gnarliest yet.
Racing the barrel section full throttle on the inside ledge today, sucked dry and the board stopped dead in its tracks.
Only a few scratches.
Next wave narrowly missed doing the same thing rode right through the inside and could see the reef coming out of the surface just behind the board.
Had to stop after 4 packs due to the rapidly receeding tide. LOL.
Wish Bob was there.
You should have seen it today.
4 to 6 foot perfection on the Batavia coast.
"Shippies" was 2 to 3 foot and breaking on reef just barely under the surface.
Just ought 3 white NQD's for $197.95,
If I keep surfing at "Shipwrecks" I am gonna need 'em.
Surfed there today, it was sick.
Biggest, cleanest, most consistent and gnarliest yet.
Racing the barrel section full throttle on the inside ledge today, sucked dry and the board stopped dead in its tracks.
Only a few scratches.
Next wave narrowly missed doing the same thing rode right through the inside and could see the reef coming out of the surface just behind the board.
Had to stop after 4 packs due to the rapidly receeding tide. LOL.
Wish Bob was there.
#4942
Senior Member
Join Date: Feb 2011
Location: West Melbourne,
FL
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
ORIGINAL: Jimi Findrix
MasiveOverkill,
Thanks Dude, 3 boardsfor under $200 delivered is a bargain.
People are charging over $230 a board on ebay lately
JIMI
MasiveOverkill,
Thanks Dude, 3 boardsfor under $200 delivered is a bargain.
People are charging over $230 a board on ebay lately
JIMI
My pleasure. It looks like Aaron just added this to his inventory.so it will probably ship from the manufacturer and once there's enough orders, he'll start stocking them in-house. Please use a gmail account if you want tracking info\updates. I couldn't get updates using my Road Runner account as I think their ISPcould be blocking it. If you have any issues with your order PM Aaron directly: http://www.rcgroups.com/forums/member.php?u=382644
I'll tell him to start an account over here. Aaron's a good guy, just remember that it may take up to 3 weeks due to customs\China Post, but people have been getting their orders in a timely manner recently.
Just spoke to Aaron and he had to raise the price a little bit to cover shipping. Price is now $69, but that's still a good deal.
#4943
Senior Member
Join Date: Apr 2010
Location: Lahaina,
HI
Posts: 432
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
massivekillover
where is the antenna on that lisa ,its going to fill up with water in 2 seconds , great price if you like to throw your money away, you might as well make your own , go custom not chinese
maui john
where is the antenna on that lisa ,its going to fill up with water in 2 seconds , great price if you like to throw your money away, you might as well make your own , go custom not chinese
maui john
#4944
Senior Member
Join Date: Feb 2011
Location: West Melbourne,
FL
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
ORIGINAL: RC HAWAIIAN STYLE
massivekillover
where is the antenna on that lisa ,its going to fill up with water in 2 seconds , great price if you like to throw your money away, you might as well make your own , go custom not chinese
maui john
massivekillover
where is the antenna on that lisa ,its going to fill up with water in 2 seconds , great price if you like to throw your money away, you might as well make your own , go custom not chinese
maui john
There are those that aren't willing to build from scratch, but are more than willing to take a pre-made hull and swap out components as it's easier to do than a scratch build.
Then there's people who buy something because it's very cheap, they don't know if they're going to like it, but they're willing to give it a try because if they don't like it or something happens to it, they're not out of alot of investment.
I wouldn't even buy an expensive model or sink awhole lot of money into something I didn't even knowI was going to like. I'm not into surfing nor really have any interest in the RC surfer myself, but guess what.............I'm alot more apt to experiment on trying something that only costs 70 bucks than I am something I have to build from scratch and\or costs twice as much.
I bet, that thischeapChineese knock-off may actually increase your business. Why? It will bring more entry-level consumers into the RC boating scene and some of those entry-level consumers may decide down the road they want something better and more customized..........that's where you come in.
#4946
Senior Member
Join Date: Feb 2011
Location: West Melbourne,
FL
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
It's funny that the first two negative replies come from an RC Surfing vendor and the next from "THE CLUB OF RC SURFING AT PRO LEVEL". Wow, the "Professional Sport of RC Surfing"...........you all have to pay dues? Do you go out and beat up amatuers who RC surf on your turf like in Point Break?
#4947
Senior Member
Join Date: Apr 2010
Location: OUTLAWS CLUBHOUSE OZ
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Why are you people attacking this guy?
He is only sharing a link to a cheap alternative to cutting up surfboards.?
You guys like to make custom boards and I think that is great.
I like to take leaky crap and make it work.
Just for the record.
I have a chinese surfer that I run really hard 8 packs a day on 1 to 3 foot reef surf and it surfs well and comes home perfectly dry.
JIMI
He is only sharing a link to a cheap alternative to cutting up surfboards.?
You guys like to make custom boards and I think that is great.
I like to take leaky crap and make it work.
Just for the record.
I have a chinese surfer that I run really hard 8 packs a day on 1 to 3 foot reef surf and it surfs well and comes home perfectly dry.
JIMI
#4949
Senior Member
Join Date: Dec 2006
Location: San Diego,
CA
Posts: 324
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
I took offense when a neewbe on his third post to our forum attacks a long time contributor with his comments...
Why don't you look at the pictures that I linked like everyone else.
why not be nice and say the antenna is clearly visible in the photos I linked to....it's the curly wire protruding from the hatch cover.
NOOOO...lets get aggro!
........whatever.
I personally don't care what kind of Surfer you Surf...as long as you Surf.
I'm not into surfing nor really have any interest in the RC surfer myself, but guess what.............
I'd like to fill in the blank...
But then JustAddWater would be at my door.
Thanks for the link...please let us know when your board arrive.
Why don't you look at the pictures that I linked like everyone else.
why not be nice and say the antenna is clearly visible in the photos I linked to....it's the curly wire protruding from the hatch cover.
NOOOO...lets get aggro!
........whatever.
I personally don't care what kind of Surfer you Surf...as long as you Surf.
I'm not into surfing nor really have any interest in the RC surfer myself, but guess what.............
I'd like to fill in the blank...
But then JustAddWater would be at my door.
Thanks for the link...please let us know when your board arrive.
#4950
Senior Member
Join Date: Apr 2010
Location: Lahaina,
HI
Posts: 432
Likes: 0
Received 0 Likes
on
0 Posts
RE: RC Surfer
Massoverkill
Sorry to have offended you, did not mean to sound so negative. I started with two Chinese Lisa's. i agree They are a good inexpensive way to see if you like the hobby,, the only problem is unless your jimi, you get water in it and shorts out,,, we are hoping the auseys are going to make one that works right out of the box,
Maui john
Sorry to have offended you, did not mean to sound so negative. I started with two Chinese Lisa's. i agree They are a good inexpensive way to see if you like the hobby,, the only problem is unless your jimi, you get water in it and shorts out,,, we are hoping the auseys are going to make one that works right out of the box,
Maui john