RE: GP Cap 232
 

You moved it into the engine box????

RE: GP Cap 232
 

Lou, yuh i moved it so the stopper is push into the firewall, i cut a hole in the firewall for the stopper, i made 2 cross beams out of a bit of triangle ply the with 3mm ply i used that as my floor i had to cut a fair bit of wood away from the fuse so i could get the tank in there and had to relocate the hardwood blocks for mounting the cowl, then i used some velcro and some spounge to hold the tank nice and firm and then i put a bit of wood behiind the tank just incase it wants to move.
but i really think this tank had to be pushed to the front, because it was way to far back for a glow engine.

RE: GP Cap 232
 

Well, all I can tell you is that mine ran just fine in the stock location with the 160 in it. Having that tank that far forward is definately going to make balancing that plane a challenge. Would sure seem like it's going to be very nose heavy at take-off and tail heavy at landings. Not a combination I would enjoy.

RE: GP Cap 232
 

Just got the new muffler in for my BCMA 40. This thing runs great! Now all I have to do is cut the new cowl and put the new wheel pants on. Should be ready to fly tomorrow if the sun melts the snow on the runway today.

RE: GP Cap 232
 

well i balanced it with no fuel in and its dead set on centre now, though yuh it will be a little bit nose heavy but it wont be that bad iam sure....i may have just got a bad engine, if this combination dont work ill take the motor back i think...

RE: GP Cap 232
 

hi guys nice looking plane.I might get one for my moki 180 that needs a home.
I just finished my hanger9 pete goldsmith cap 232g MVVS58 & my 1/3 scale cap 580 with a QS3W106 is 3/4 built.
im a capaholic so this looks like a nice nitro bird
cheers glen

RE: GP Cap 232
 

Glen,

Like you, I'm a Cap-a-holic. I just gotta fly everyone I can get my hands on. If I were to take stock and I will do just that, I have flown/owned:

GP Cap 580 40 size (owned, sold)
GP Cap 580 33% (owned, sold)
GP Cap 232 27% (currently owned)
The original H9 Cap (just flown)
Carden Cap 232 all three sizes: (30, 35, and 40 percent) (I wish I owned any one of these [X(])
WM Cap232 (40 size) (owned, sold)

If I were to compare between these, I would say this GP version flies very close to the Carden 30%. But the best of those ones I flown by far is the Carden 40%. Now there is one stable Cap. :D

So as not to take this thread to far away from the GP Cap, would you mind very much me asking you to PM me with any details you can give me about the H9 Cap. Anything you can think of like how it flies, power to weight, mixes, aerobatics, things like that.

RE: GP Cap 232
 

My wife loved the colors on "H9", it looked impressive especially in comparason with "GP" some of the early pics that blue on "GP" CAP have a pearl flope in it, so on most of the pictures that blue looked pale light, in other word terrible, but when I saw plane in a real life it looked to me "Tomy Helfiger" like color shrime biutefull.(do not mighn my spelling plz.)

Hower, colors do not fly planes. At over 17Lb and little more than 100sq in "H9" CAP according to our club member, from whom I just picked "GP" 27% CAP(light crash special), while he was finishing up "H9", it is a "flying brick". He thinks that in "H9" evevator stab is too high, but I think the weight is a culpit. It is in my opinion is over enginered(not only it have main wing tube, but elevator tube as well), but eventhough it is CF it is still adds wight. Tail wheel in "H9" CAP is a machined aluminum master piece marvel, in "GP" tail wheel is cheap and hamble cost $1.89, I end up installing it on all of my size 40 and 60 "3D fun flyes" models, works great("Ford over Ferrary" rule works between this two plane like a charm), but like thier "ShowTime" for almost noting to glue when building the plane thumes up, but for tip stalling in the air thums down. I would like to hear if any one have a luck 3Ding "H9" CAP, I'm still druling over looks of this plane, but ultimatly I whant to 3D more than just looking at the airplane!

RE: GP Cap 232
 

sweet sounds like you love them alot.
i have had
2xWM castrol 40 size crashed doing low ke
2x 50cc both hanger 9 airatilia purple one died still have the other pete goldsmith
1x hanger nine 100cc still got it & love it
1xcap580 100cc in the build now & cant wait to fly it next weekend
& my brother has the pheniox models cap with a dzy48
3x mini craft caps moki 180 all dead but:( & i loved them.One was called the $50 cap see the pic with a $50 note stuck on the wing
a few pics
I got a 2.6 red bull yak & wish it was a cap[:-]sshhhhhhhhhh dont tell bully but lol
buying a carden 40% kit in a few weeks for my new 3W157TSCS
cheers glen

RE: GP Cap 232
 

Blockbuster,

I appreciate the info on the H9 version....

The GP version 3D's very well. A few pages ago, I posted a link to a video of a member by the name of whaturi that I fly often with. He is flying my first one (as you nicely say, light crash giveaway) on an OS160. He has also flown mine with a DA50 at 14lbs and loved it.

The stab on the H9 Cap is actually right where it should be. The GP is a tad lower but looks to be almost directly in line with the thrust line. With the wing area on the H9, at 17lbs it's pretty high on wing loading. It's that high position that makes the elevator so effective with minimal throw needed.

Glenn,

Oh yea, I'm a big Cap fan. When I flew full scale, I did my aerobatic training in an Extra a Stearman and an Agcat and got to wring out a Cap. You could get the thing right up to the stall and just as the plane would shudder, corner the stick, stomp the rudder go to full power and she would just tumble ever so slowly. Release pressure on the stick and rudder and as soon as you get to the position you want, kick the rudder ever so slightly and release quickly and she'd stop right then and there. The GP Cap is a lot like that. Pull into a 45 degree climb and slow down, roll into a left wing down KE, put the left stick in the upper right corner (fullpower full right rudder) and the right stick in the upper left corner (full down and full left aileron) and hang on, you should get about 2 or 3 tumbles and she'll fall into a nice inverted flatspin. It's even better doing it from inverted. Just add the rudder and power as described, hold it for a second or two while waiting for the plane to start slipping sideways, the add the elevator/aileron as described and the next thing you know is you are still flying sideways rotating right around the CG. sorta like a KE spin only level instead of dropping. It's all a matter of timing but once you get it, it's a great site and is what a Cap does really well and the best thing is low rates as described in the manual are plenty. On high rates she is blindingly fast

I'm jealous. I've wanted a Carden version for some time. There was one in the marketplace a few weeks ago, a 30% I think that was really nice in price and absolutely gorgeous. It was not sold and hopefully it will pop up again.

RE: GP Cap 232
 

now im jelous bubba you been in the real deal ,oooohhhh man i day i hope to ,,
great info thanks for the heads up you capaholic:D no 3 step programe for your addiction lol
your in to deep[X(][8D]
regards glen

RE: GP Cap 232
 

Well she's ready to go. All I need now is for the snow to go away long enough for me to fly the darn thing!!!![:o][:o][:o][:o]

RE: GP Cap 232
 

Lou,

What's she weigh?

Glenn,

They better never find a treatment for this addiction. I'll resist it at all costs. I don't want to be cured, this is way too much fun....

RE: GP Cap 232
 

Lou: looks great! I can believe how stable this Cap is. I've tone the throws to lowwwwww and it flys great. The Fuji has been flawless so far (unless I forget to UN-choke it......damm that choke) with plenty of power for sport flying. This was my first gas engine and I'm looking for another gas motor and plane already! I may try the Fuji 32b on a GP Giant Stick, PUTT-KNOCK around the sky......I looked at your Bio- Retired Air Force, great! I'm retired Marine....life is good!

RE: GP Cap 232
 

Well, I've totally talk myself into get one of these Caps. With help from you guys of course! I'm still deciding what to power it with. I'm leaning real hard on the OS 160, as Bubba and Lou, Whaturi and Maudib said it will fly the heck out of it. Thanks for answering all my questions by the way. The DA 50 is alittle more than I want to spend on this bird right now. Might be a good choice down the road with maybe a 85 inch plane. To make matters worse, I'm really wanting to get my feet wet with a gas plane. As long as I'm sure I wont have any fuel issues with the 160, I think it will be a great combo. Tower is gonna get a order real soon... Ahh, decisions decisions[sm=spinnyeyes.gif]

RE: GP Cap 232
 

AUW is 13lbs 10ounces with 20+ pounds of static thrust. Should work out just fine when the weather gets here.

Hey Sewerdude, If you order the CAP and teh 160 from Tower be sure and split up the order into $150.00 segments and take the $25.00 off each segment, beats the heck outta the combo deal!

RE: GP Cap 232
 

Got ya Lou! You must of been reading my mind. :D

RE: GP Cap 232
 

How about one of the Brillelli engines. I do not have one just yet bu a few RCU members whose opinions I trust have them and just love em. I'm considering the 60cc one for a 2.3m Extra

http://brillelli.com/brillelli_engines_002.htm

RE: GP Cap 232
 

Hello, Sorry to jump in. I've been following this forum for some time. I just finished with my GP cap a couple of weeks ago. I've had the bird framed up for about 6 months while I was trying to figure out the best set up for extreme 3d. My innitial plans were to go with the BME 55 but it was taking too long to be released. Next up was the DA 50. Everyone seemed to be coming around 13lb with this engine. I saw whaturi's video and was impressed with how light it seemed to fly. If I remember correctly his was around 12lb 4oz. But it did look like it was flying with barely enough power for 3d with the OS 160. His video made me look into glow. So I started weighing engines and wound up going with the saito 180 (34oz with muffler at least mine is from loosing the end from vibrations so I welded a os 40fp exhaust end on and drilled out the exhaust hole). I pulled the 180 out of my DP ultimate which weighed 11lb 4oz it hovers at about 1/2 throttle with decent pull out. So if I kept the weight at 11lb or so it would have good power with a really good wing loading. When done, my completed wieght is 10lb 13oz.:D
Here is my set up and how I kept it light.

Lightened hatch (removed flooring)
Lightened wheel pants
Lightened axles and Kavan wheels
modified tailwheel
Lightened motor box
Atached cowl directly to fuse didn't use hardwood blocks
HS 5645 surfaces GWS micro Throttle
1250 mah Lipoly batt 6v regulator
Lighwieght switch
kevlar pull pull
Carbon ultimate spinner
Carbon Mezjlik 18x6 prop
Hangar 9 titanium links dubro clevis
Fliton aluminum control horns
Coke bottle 16 oz tank
Wing and tail surfaces untouched
I guess my best analogy is instead of sticking a Viper V10 engine in a honda civic I just shed a 1000lb[8D].

I have about 6 flights. This is one awesome plane. Hovers at less than half throttle excellent pull out. This plane flies lika a foamie. If I stop a manuver in almost any posistion and leave a little power on it just floats there. I'm no expert flier but it makes me feel like one. My only complaint it that the landings arn't easy. The plane is so light I have to feed a lot of down elevator to land. It is balanced at 6 1/2 so it is at the rearmost cg but it's hard to stall it, I have to slow it down almost to a complete stop. Can't wait to get some more stick time.
I know, Long post.
Here are some pics.

RE: GP Cap 232
 

More pics

RE: GP Cap 232
 

Lightened wheel pants

RE: GP Cap 232
 

Now,
that's a really nice plane!
I fell in love with it!!!:D

RE: GP Cap 232
 

You know the wheel pants thing is a great simple idea....

Thanks,

Hibrass

RE: GP Cap 232
 

kwboost,

Now there is a really nice glow setup.

In whaturi's video, the main problem was the prop he was using. It was a ProZinger and they great at stirring paint and beating up the air to make noise. He did start out on the APC18X6W and though it was much better in the power department, he hated the spoolup time.

It really looks like you saved about as much weight as you could short of pulling the covering off and going at it with a dremel. You even did it and managed to keep the wheel pants on and use a spinner. This plane just flat out looks ungly without either of them, at least to me

Again, that's a really nice layout

RE: GP Cap 232
 

bubbagates,
I agree with you. I hate to see a scale plane without wheel pants or a spinner.
Hibrass,
I sat around and thought of every possible sensable way to save weight. This saves a few grams but it ads up.