RE: the hyper st PRO thread!
 

just finished the shocks,i went with 50 front and 45 rear,our track is not very bumpy so i think its a good starting point.i also have 7f,10c,3r on the diffs.my only question now is ride height and drop limiter.thanks

RE: the hyper st PRO thread!
 

anyone know if the Hyper ST Pro body will fit on the Hyper ST RTR without any modification? If not what are some other bodies that will fit? I don't want to get another RTR body, I would like a custom paint job.

RE: the hyper st PRO thread!
 

Yupp the Pro bodies fit, as a matter of fact, they even come with pre-cut holes to mount the body in the RTR.

Example; Notice the holes

http://i231.photobucket.com/albums/e...7/0caa80d2.jpg

And the bodies of the X1 CRT fit fine, and Ive read somewhere that you can get a Mugen body to fit ( Go a few pages back, PatrickBW got one to fit ), and the Kyosho ST R bodies fit too ( Read it on another forum ).

RE: the hyper st PRO thread!
 

Thank Qaiz!

RE: the hyper st PRO thread!
 

Does anyone know if Pro Line Crime Fighters will fit on the Hypers ST Pro rims?

RE: the hyper st PRO thread!
 

Im pretty sure they will, tho double check that. Guy at my LHS said they'll fit, but I dont trust him :D.

RE: the hyper st PRO thread!
 

No they wont fit.
Traxxas Response and Panther Pythons tyres will fit the ST rims.

RE: the hyper st PRO thread!
 

Definitley NO!!
Phil

RE: the hyper st PRO thread!
 

the crimefighter lpr fit with some modding. you have to cut off the little lip inside all the way around. i did some panther gators that way and its worked great so far.

RE: the hyper st PRO thread!
 

Finally got around to taking out my front and rear diffs due to them leaking. And boy did they leak. Both Empty. That red rubber band that seals the front and rear diff to the main gear is a joke. When taking it apart I compared it to my brother-in-laws Kyosho Inferno Buggy and guess what. The Front and rear diffs are identical down to every part. The thing about the Kyosho Inferno buggy diff is it also has a gasket inbetween the diff cup and the main gear. So I order it and it was a perfect fit. Cleaned out the diffs relubed put them back together plus the new gasket. So for anybody looking to fix the leak with the front and rear diffs here is the part I used.

[link=http://www.amainhobbies.com/product_info.php/products_id/4144]http://www.amainhobbies.com/product_info.php/products_id/4144[/link]

While we were at it my brother-in-law also fabricated some new gas tank posts as the stock ones just don't cut it. We made them alittle thicker and used small rubber orings to dampen the tank from vibration. Works like a charm.

Here are some pics of the new mounts.

After all the new mods went out for a test run and the mounts and new gaskets worked like a charm. Kudos to Jerzferno for making the new mounts.

RE: the hyper st PRO thread!
 

was bumed had my first night race for my hyper st pro was in third and i guess when i pitted my guy didn''t fill the tank up all the way i was bumed but o well different pit guy next time thats for sure

RE: the hyper st PRO thread!
 

Well giving my ST a new look. All Black, everything will be black + purple. Waiting on a body from the LHS, if its not here by Saturday, im gonna buy a X1 CRT Body and paint that black. I absoloutely love the black + purple look of it.!

http://i231.photobucket.com/albums/e...7/bde0c340.jpg

http://i231.photobucket.com/albums/e...7/f3948529.jpg

http://i231.photobucket.com/albums/e...7/9a83ee1f.jpg

http://i231.photobucket.com/albums/e...7/8714e2a6.jpg

Also got a new flywheel + clutch today. Old one was completely knackered.

RE: the hyper st PRO thread!
 

http://www.amainhobbies.com/product_...ducts_id/23021

would this be a good motor for my hyper st and has any one ran it before?

I had a Jammin .28 but ive given up on it its had problems since the start always stays way to lean never holds a tune ive sealed the whole thing I run side winder 20% stock 3 shims on the head and called ofna they said theres nothing they can really do they said maybe add another shim sooo yeah in need of a new motor on the cheaper end

RE: the hyper st PRO thread!
 

Are you sure your supposed to be running 3 shims.? I think it was 2 with my Picco, and they're the same engines. I run 3 shims and im running 30%. Have you tested the engine for air-leaks.?

Take a look at this one, a coupla guys run them at the track,

http://www.amainhobbies.com/product_...ducts_id/22974

RE: the hyper st PRO thread!
 

Spikeit - I think we got that truggy smokin fast now. Just need to tighten up all those fasteners and blue locktite them. And watch out for that double jump on the long back stretch. Dont know why, but that truggy thinks its an air plane? Keep it low and you'll do great this Sunday!

RE: the hyper st PRO thread!
 

Agreed. The Hyper has no issues. It's all driver now. And that double should be a triple now.

RE: the hyper st PRO thread!
 

i left it the way it was they told me to add another shim even to lower compresion so dosen't run as lean so idk unless ofna tech was wrong but im not for sure what shims to leave it at soo any one got better idea on that

RE: the hyper st PRO thread!
 

So True lol.


Check your manual, Im pretty sure its supposed to be 2 Shims for 20%, and 3 Shims for 30%.

Just double check what your Instruction Manual says.

RE: the hyper st PRO thread!
 

idk what would be for 20% said in the manual it was shimed for 20% i dont know how many shims that is though has three in it havent mesed with it and honeslty just sick of it has never held a good tune witch sucks so im really gettin over it and lookin for a new engine somethin i dont wana do cuz this engine isnt that old haha but o well

RE: the hyper st PRO thread!
 

http://www.amainhobbies.com/product_...oducts_id/6406
http://www.amainhobbies.com/product_...oducts_id/6008
http://www.amainhobbies.com/product_...ducts_id/23021

not sure on which to get would any of you recomend any 1 out of the other in that group of engines?

thanks

RE: the hyper st PRO thread!
 

I have the OS V-spec. It's got plenty of power, great run times, reliable, and easy to tune.

RE: the hyper st PRO thread!
 

Guys.

Can someone post me a pic of what kind of stick pack your using.

Reason being, my old one died on me today, and nearly took my car with it.

I got 5 Energizer 2500MAH batteries, and am gonna build my own pack, ( Ive done it a lotta times before for friends ). And I need to see how you mounted it.

Im thinking 3 - 2 Formation, because a 5 formation wont fit right.

Thanks.

RE: the hyper st PRO thread!
 

i just put the ninja 21 in my st last week. i was surprised how good it pulled the hyper. the motor was not
new, 6 or 7 gal thru it. it was actually easier to drive, putting the power to the ground was no problem.

RE: the hyper st PRO thread!
 

hmm vspec or ninja both at same price both sound good any better pros or cons or anything or both great engines i just gota pick one?

does the vspec come with the same carb as the O.S. .28

RE: the hyper st PRO thread!
 

Qaiz, I use a 1600 MAH stick pack something like this.

http://www.amainhobbies.com/product_...ducts_id/20047

I get at least three tanks and I am running a JR 9100T and a hitec 645. I usually charge it after three because I do not want to take any chances.

I use the longer battery cover pictured here.

http://www.amainhobbies.com/product_...ducts_id/13786