RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 10
1
2
3
Last »
Search: Posts Made By: abacro
Showing results 1 to 25 of 239
Search took 0.79 seconds.
Forum: Gas Engines
01-09-2018, 07:38 PM
Replies: 19
Views: 1,325
Posted By abacro

I have the same engine , it is a Walker 2.4 The...

I have the same engine , it is a Walker 2.4 The offset crank case bolt is a dead give away of the Walker then later A&M engines.
Forum: Gas Engines
12-22-2017, 04:59 PM
Replies: 9
Views: 1,746
Posted By abacro

If you built the Clipped wing version of the...

If you built the Clipped wing version of the Lanier T-craft ( the 87 inch span ), then yes a YS 120 four stroke will fly it no prob. But the full 9ft span T-craft comes in at roughly 18 to 22 pounds...
Forum: Gas Engines
12-21-2017, 08:05 PM
Replies: 9
Views: 1,746
Posted By abacro

Take it from someone who has had that T-craft,...

Take it from someone who has had that T-craft, NEITHER the G-23 or 38 will fly it! Get at least a 45 of any class, I ended up running a G-62 in mine off floats. Just a added tid-bit watch the rudder...
Forum: Questions and Answers
08-10-2017, 12:30 PM
Replies: 14
Views: 817
Posted By abacro

How you are running with Both modules hooked up...

How you are running with Both modules hooked up is beyond me. There should be no way that the 2 modules will work at the same time hooked up together. One { PCM} should and will OVERRIDE the plain FM...
Forum: Questions and Answers
08-09-2017, 11:02 AM
Replies: 14
Views: 817
Posted By abacro

Your Module is transmitting in FM even when it is...

Your Module is transmitting in FM even when it is in the 2.4 PCM mode. Just when you switch it from PCM to PPM you are noe still in FM but you turned off the Pulse code signal. FM is a wavey signal...
Forum: Gas Engines
08-08-2017, 12:48 PM
Replies: 6
Views: 1,296
Posted By abacro

Ok ,since it is running on the prime every time ,...

Ok ,since it is running on the prime every time , your problem is the diaphragm is set to low. Your not opening the needle seat to let fuel in. Try raising the little tab on the needle holder up till...
Forum: Questions and Answers
08-08-2017, 12:41 PM
Replies: 14
Views: 817
Posted By abacro

Great its working but now you need to see what...

Great its working but now you need to see what Frequency your on. Going to ppm you are no longer in the 2.4 range I believe. You are back into the radio's original FM frequency now. That is the...
Forum: Gas Engines
08-07-2017, 12:40 PM
Replies: 6
Views: 1,296
Posted By abacro

Your PULSE tube is blocked! the little hole in...

Your PULSE tube is blocked! the little hole in the carb block that actuates to diaphram. Your not getting the engine pressure needed to work the pump. That's the only thing I can think of short of...
Forum: Questions and Answers
08-07-2017, 12:34 PM
Replies: 14
Views: 817
Posted By abacro

The Challenger 720 radio is NOT compatable with...

The Challenger 720 radio is NOT compatable with the 2.4 modual you hooked it to. Your problem is , you hooked up a HELICOPTER CCPM module to a FIXED wing only aircraft radio. The 720 has no Mixing...
Forum: Beginners
06-18-2017, 01:46 PM
Replies: 6
Views: 639
Posted By abacro

I had a 1/4er scale TaylorCraft , the G-23 is NOT...

I had a 1/4er scale TaylorCraft , the G-23 is NOT enough power for it even on wheels! The G-38 is a bit better,but if u want TRUE TaylorCraft performance IE. ( will Knif edge flight,fly inverted,do...
Forum: Glow Engines
03-10-2017, 01:05 PM
Replies: 1
Views: 649
Posted By abacro

No,that is the normal setting on the YS 4...

No,that is the normal setting on the YS 4 strokes. I have 8 of them from the 53 to the 170 and all of them seam to run between 3/4er of a turn to 1 1/4er turns open from fully closed. I believe it's...
Forum: Questions and Answers
07-13-2016, 04:04 PM
Replies: 21
Views: 1,912
Posted By abacro

Take the muffler off the 120 and watch it come...

Take the muffler off the 120 and watch it come alive!
Forum: Beginners
07-02-2016, 05:58 PM
Replies: 4
Views: 744
Posted By abacro

The engine is a Enya 53 not a 54,and the plane...

The engine is a Enya 53 not a 54,and the plane looks to be either a modified 4star 40 or a scratch built Hot's.Both planes fly extremely well and the Enya is a perfect match with any good 11/5 to...
Forum: AMA Discussions
12-15-2015, 09:02 PM
Replies: 0
Views: 344
Posted By abacro

UAS's and FAA registration Question

Since by the FAA standards EVERY single Aircraft over .55 pounds is a UAS. Who is going to let ALL the people in the country buying the Airhogs,and all the other Drones with cameras on them for their...
Forum: Gas Engines
11-15-2015, 02:58 PM
Replies: 2
Views: 618
Posted By abacro

Brisson will have an adapter hub for it.

Brisson will have an adapter hub for it.
Forum: Questions and Answers
09-29-2015, 08:39 AM
Replies: 5
Views: 539
Posted By abacro

the 15/10 is the same as the 16/8 ur running now!...

the 15/10 is the same as the 16/8 ur running now! just a smaller diameter to allow for ground clearance! General guide to 120 prop sizes I've found is 14/10 or 14/12,15/6 to 15/12 and 16/4 to 16/10...
Forum: Glow Engines
09-29-2015, 08:32 AM
Replies: 10
Views: 4,009
Posted By abacro

No airbleed carbs on my 40's all have a low side...

No airbleed carbs on my 40's all have a low side needle valve.
Forum: Glow Engines
09-29-2015, 08:29 AM
Replies: 24
Views: 3,788
Posted By abacro

Sorry to hear that someone put a airbleed carb on...

Sorry to hear that someone put a airbleed carb on the engine.The problem your having can only be cured by putting the correct carb or equivalent sized carb to the original one back on the engine.The...
Forum: Glow Engines
09-28-2015, 01:03 PM
Replies: 24
Views: 3,788
Posted By abacro

here is the correct low speed needle setting...

here is the correct low speed needle setting according to OS. Close the throttle barrel till just the tip of a pin will slide in,then while blowing on a piece of fuel line hooked to the carb inlet,{...
Forum: Glow Engines
09-28-2015, 12:51 PM
Replies: 10
Views: 4,009
Posted By abacro

I have 8 of the 40 fsr's 2 of the 45 fsr's and a...

I have 8 of the 40 fsr's 2 of the 45 fsr's and a 60 fsr, they all seem to run the best to me on 15% nitro and Fox RC long idle bar plugs. They will eat glow plugs so I don't buy the high priced OS...
Forum: Questions and Answers
09-28-2015, 12:33 PM
Replies: 5
Views: 539
Posted By abacro

run a 15/8 u'll see a big difference in...

run a 15/8 u'll see a big difference in performance
Forum: Questions and Answers
08-24-2015, 07:43 PM
Replies: 8
Views: 670
Posted By abacro

its no Quadra its some ones Weed eater conversion...

its no Quadra its some ones Weed eater conversion has wrong crank case to be a Quadra
Forum: Gas Engines
08-19-2015, 07:59 AM
Replies: 3
Views: 645
Posted By abacro

You can also use the Champion RCJ8 plug,if u cant...

You can also use the Champion RCJ8 plug,if u cant find the NGK,
Forum: Glow Engines
07-11-2015, 08:01 AM
Replies: 21
Views: 2,928
Posted By abacro

Thank you guy's for clearing that up for me. It...

Thank you guy's for clearing that up for me. It now makes total sense so I guess in FACT it really WAS me! lol lol :)


Art
Forum: Glow Engines
07-10-2015, 04:52 PM
Replies: 21
Views: 2,928
Posted By abacro

.Maybe it's just me but on the motors with the...

.Maybe it's just me but on the motors with the removable front housings like the OS FSR's. How in the heck does simply rotating the front housing AKA .(carb mount and bearing holder) 90 degrees...
Showing results 1 to 25 of 239
 
Page 1 of 10
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.