RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: brazoski
Showing results 1 to 15 of 15
Search took 0.42 seconds.
Forum: RC Truggy
03-12-2010, 04:17 PM
Replies: 7
Views: 1,188
Posted By brazoski

RE: anyone have a rc8 or a mugen truggy

I have a set of the Kyosho big bores i would let go for 50.00 if you're intrested.
Forum: RC Truggy
02-15-2010, 08:36 PM
Replies: 11
Views: 3,654
Posted By brazoski

RE: RC8T Diff Problem HELP

I do not think the problem is the shims. You should have 2 shims under each large gear and one on each of the 4 smaller gears. Make sure the large gears are all the way down on the cross pin on the...
Forum: Car Nitro & Gas Engines
09-11-2009, 12:39 PM
Replies: 341
Views: 45,192
Posted By brazoski

RE: PowerHouse RC Performance Race Engines

A question for Mark and or Adam, have you looked at the new Jammin JPX21 plus yet.
Forum: Car Nitro & Gas Engines
05-28-2009, 11:12 PM
Replies: 21
Views: 1,867
Posted By brazoski

RE: Picco 28 breakin issues

This may sound stupid but are you sure the starter box is turning the motor correct way?</p>
Forum: Car Nitro & Gas Engines
05-10-2009, 07:13 PM
Replies: 40
Views: 4,015
Posted By brazoski

RE: JPX 21, what to expect

Rear bearing is 14 x 25.4 x 6 never had a problem with a front bearing. Nova inserts are same dia but longer.
Forum: Car Nitro & Gas Engines
05-07-2009, 12:14 PM
Replies: 40
Views: 4,015
Posted By brazoski

RE: JPX 21, what to expect

I have one with about 9 gallons on it. Spent most of it's life in a truggy with 053 pipe. Plenty of power with 8.5 to 9 min run time. Watch the rear bearing at around 1.5 to 2 gal.
Forum: RC Truggy
02-05-2009, 01:19 PM
Replies: 12
Views: 911
Posted By brazoski

RE: Kyosho Diffs in CRT

With the Kyosho gearing you should run 13/50 on the clutch/spur.
Forum: RC Truggy
01-04-2009, 11:43 PM
Replies: 6
Views: 718
Posted By brazoski

RE: Texas Newb here!

You have alot of nice tracks in your area, San Antonio, Boerne, and Austin. Try some of the club races and you will be hooked.
Forum: RC 1/8th Scale Buggies
01-01-2009, 01:44 AM
Replies: 29
Views: 2,330
Posted By brazoski

RE: Question About Using A Rubber Band

Yup, been on there 2 years, pulled 3 servo's back that quit during racing. I haven't opened the bag of carb "o's" since I bought them. Granted I don't race in the winter so if your a year round...
Forum: RC Truggy
12-12-2008, 11:33 AM
Replies: 19
Views: 1,408
Posted By brazoski

RE: How to get more oversteer?

Make sure your servo saver is set tight enough. If your front tires are not staying turned under power tighten the saver.
Forum: RC Truggy
08-20-2008, 01:01 PM
Replies: 1,326
Views: 110,001
Posted By brazoski

RE: - Official Kyosho MP777 ST-R Thread -

Yes you put the end of the boot over the shock end and the spring retainer holds it there.
Forum: RC Truggy
08-20-2008, 12:58 PM
Replies: 16
Views: 1,086
Posted By brazoski

RE: Info needed asap!!!!!

Kyosho is a great company. I run a Kyosho buggy and truggy. That being said do not buy their ready to run. If you are going to go rtr you are probly beter off with a different brand.
Forum: RC Truggy
03-17-2008, 11:48 AM
Replies: 95
Views: 5,092
Posted By brazoski

RE: [Awaiting Approval]

The instructions that came with my P-3 are wrong on the low speed needle settings. It says to set low 10.5 to 11.5 out. That is way to rich. I belive the low should be about flush.
Forum: RC Truggy
02-22-2008, 05:40 PM
Replies: 1
Views: 431
Posted By brazoski

RE: Ace ds1015?

3 mm
Forum: RC Truggy
07-26-2007, 10:44 AM
Replies: 2
Views: 503
Posted By brazoski

RE: kyosho st-r diff gears?

Yes they will work and are better than Kyosho's
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.