RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: APMECH
Showing results 1 to 15 of 15
Search took 0.66 seconds.
Forum: Futaba Radios Direct support forum
02-25-2016, 09:54 PM
Replies: 2
Views: 545
Posted By APMECH

Thanks for the info.

Thanks for the info.
Forum: Futaba Radios Direct support forum
02-25-2016, 09:54 PM
Replies: 2
Views: 2,064
Posted By APMECH

Thanks for the quick reply.

Thanks for the quick reply.
Forum: Futaba Radios Direct support forum
02-25-2016, 08:44 AM
Replies: 2
Views: 545
Posted By APMECH

SBS-01G Altitude

Is there a way to have the sensor output gps altitude instead of barometric? The reason I ask is because when I fly air is moving through my model and the faster the model goes the faster the air...
Forum: Futaba Radios Direct support forum
02-25-2016, 08:09 AM
Replies: 2
Views: 2,064
Posted By APMECH

voice alerts

The 'Motor' function in my 14sg has a main switch to enable the motor but there is also one called start switch on the Motor function setup screen. I don't see the start sw in the motor function of...
Forum: Futaba Radios Direct support forum
02-23-2016, 08:13 AM
Replies: 2
Views: 744
Posted By APMECH

Thanks for the quick reply. The 'Motor' function...

Thanks for the quick reply. The 'Motor' function in my 14sg has a main switch to enable the motor but there is also one called start switch on the Motor function setup screen. I don't see the start...
Forum: Futaba Radios Direct support forum
02-22-2016, 09:34 AM
Replies: 2
Views: 744
Posted By APMECH

18SZA Programming

I just purchased the 18SZA to replace my 14SGA. While manually programming the 18SZA from my 14SGA I noticed 2 significant differences that I need help with.
1) On the 14sga I have the "Motor"...
Forum: RCV Engines Support
06-01-2009, 09:03 AM
Replies: 2
Views: 2,005
Posted By APMECH

RCV 58 CD dead

On an earlier post, I mentioned a chirping noise. The noise went away completely so I felt there was no need to send the engine in for repair. I probably should have. I had my first dead stick...
Forum: RC Warbirds and Warplanes
03-26-2009, 10:34 PM
Replies: 18
Views: 1,865
Posted By APMECH

RE: First Warbird Suggestion?

I've got a VQ warbirds p-40. I am also looking at their p-51. Built solidly but easy to assemble and has all the hardware.
Forum: RCV Engines Support
03-18-2009, 09:06 PM
Replies: 1
Views: 948
Posted By APMECH

Chirping Noise during Idle RCV-58

Hello,

I have purchased a RCV58CD and a RCV91CD the 58 for use in a Great Planes Escapade, and the 91 for a VQ P-40. I have only run the 58 so far. Doing the running in procedures. It seems...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
03-07-2007, 03:11 AM
Replies: 21
Views: 5,197
Posted By APMECH

RE: 2.4 GHz vs 72 MHz - Free space loss

I sit corrected ;), Thanks for that cool Info!!! When doing chamber testing in emc everything is done pretty much at 1M so the fresnel zone never really came into play. Maybe that's why all the...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
03-06-2007, 03:32 AM
Replies: 21
Views: 5,197
Posted By APMECH

RE: 2.4 GHz vs 72 MHz - Free space loss

This is an interesting suject to me.
I used to be a electro-magnetic compatibility test technician for automotive components. And as a general observation, the higher the freq the lower power...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
03-05-2007, 01:34 AM
Replies: 7
Views: 753
Posted By APMECH

RE: My receiver antenna wire is torn, is this ok or not.??

Best bet is to send it back to mfg to have them solder a new one on. They usually frequency check them afterwards to ensure proper tuning. Antenna length is fairly critical for range and making sure...
Forum: Beginners
05-14-2003, 03:11 AM
Replies: 7
Views: 858
Posted By APMECH

Flap controlled remote glow?

I use "OptoGLoII" from http://www.cliftech.com you can purchase the kit which you just need to drill the holes and install the components. Only $25. You will need a batt harness and a glow driver...
Forum: Tips & Techniques
05-07-2003, 08:57 AM
Replies: 1
Views: 460
Posted By APMECH

Accessory Module

Have you looked into an rc switch that you can run in parallel with another channel? There is an optically isolated switch that you can run off a "Y" harness lets say off of your gear channel that...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
05-01-2003, 09:10 AM
Replies: 18
Views: 1,592
Posted By APMECH

Futaba 6xas- or JR 622

Actually the amount of circuitry integrated on a board and with the use of smds can greatly reduce the amount of internal interference the unit generates. Most radios made since the late 90's use...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.