RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: cadmn
Showing results 1 to 17 of 17
Search took 0.40 seconds.
Forum: RC Jets
12-14-2009, 02:48 AM
Replies: 32
Views: 6,759
Posted By cadmn

RE: STOLEN JET!!!!!

the same type of POS that steals A radio box & misc. supplies box by breaking a window in a vehicle in a driveway I had a box stolen with 8c & buddy box in it & police said "too bad soo sad" & my...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
05-08-2009, 12:52 AM
Replies: 4
Views: 712
Posted By cadmn

9C & rubber duckie antenae

I have been told by some that a rubber duckie & a 9C will not be dependable because Futaba does not recognise this antenna. I've also been told by others that they have flown this configuration for...
Forum: Questions and Answers
12-14-2008, 08:13 PM
Replies: 15
Views: 3,449
Posted By cadmn

RE: 2-56 and 4-40 threaded rods

Most rods I get use 2-56 threads & can easily be cut with a die of that size & most all connections come in that size.
Forum: General Racing Discussion
01-26-2008, 08:22 PM
Replies: 26
Views: 2,283
Posted By cadmn

RE: Viper or Predator II?

skull we will be holding the third & final winter mini series race on feburary 10,2008 then start the 2008 series in march the winter mini has been a good setup/proving ground in prep for the series...
Forum: Composites Fabrication And Repair
07-20-2007, 09:41 PM
Replies: 12
Views: 1,756
Posted By cadmn

RE: what kind of FG mold separator

PVA=Poly Vinyl Alcohol so why we thinning with water? thin with denatured alcohol! after first part pulls good, Just use wax, couple of good coats each part & should be fine
Forum: Composites Fabrication And Repair
07-20-2007, 09:23 PM
Replies: 7
Views: 1,050
Posted By cadmn

RE: What do i need and where can i get it

sorry but I must dissagree Matt & cloth are TOTALLY different being from that industry. Cloth is like a silk material where the threads are woven togather in a pattern. Matt is fibers bound...
Forum: Profile and Fun Flying Planes
07-19-2007, 09:34 PM
Replies: 8
Views: 923
Posted By cadmn

RE: Help please

the LE is straight, thanks for all the help guys the fuse is thin Profile, guessing 1/2" ply
Forum: Profile and Fun Flying Planes
07-19-2007, 09:30 PM
Replies: 8
Views: 923
Posted By cadmn

RE: Help please

the LE is straight
Forum: Profile and Fun Flying Planes
07-19-2007, 12:33 AM
Replies: 8
Views: 923
Posted By cadmn

Help please

can anyone Identify what this plane is? I know its very quick in reaction Time &will be good for 3d stuff I am told
Forum: Composites Fabrication And Repair
07-17-2007, 10:49 AM
Replies: 7
Views: 1,050
Posted By cadmn

RE: What do i need and where can i get it

the more layers the more crossed fibers hence strength resin alone is brittle the fibers give it strength. I like Matt instead of cloth
Forum: Composites Fabrication And Repair
07-17-2007, 10:40 AM
Replies: 27
Views: 7,534
Posted By cadmn

RE: Ok, I give up, what's the trick to vacuum bagging

guys we always used the heavy fg cloth as a breather ove the entire part with a peal ply against the layup the cloth allows the suction to spread evenly accross the part & make sure the excess resin...
Forum: Composites Fabrication And Repair
07-17-2007, 10:24 AM
Replies: 9
Views: 1,198
Posted By cadmn

RE: HELP !!! What am I doing wrong ?

or you can bake your plaster plugs in oven for awhile at 200 degrees & as stated by ED above make sure of no undercuts/reverse Tapers I have seen many a good mold/plug ruined by undercuts
Forum: Composites Fabrication And Repair
07-17-2007, 10:17 AM
Replies: 12
Views: 1,756
Posted By cadmn

RE: what kind of FG mold separator

OK use pva on first part as safety precaution of sticking after layers of wax buffed good once first piece is pulled then look to see if pva is on part & not mold if on part in full sheet the wax &...
Forum: AMA Discussions
05-15-2007, 09:36 PM
Replies: 84
Views: 6,921
Posted By cadmn

RE: AMA and Young Guys

well as I see it you pay well for the greenskeeper to keep up the greens you play on so pay to keep up the field you fly on it seems it all the old guys doing the needed work on the field & in the...
Forum: RC Warbirds and Warplanes
03-12-2007, 11:03 PM
Replies: 28
Views: 3,381
Posted By cadmn

RE: nitromodels anyone?

I have the P-40 warhawk I oredered over the phone & was told retracts came with I being new didn't realize untill a buddy came over & answered questions for me then told me there was no retracts in...
Forum: Giant Scale Aircraft - 3D & Aerobatic
11-29-2006, 08:25 PM
Replies: 22
Views: 1,832
Posted By cadmn

RE: Lockheed Martin AFSS needs donated giant models!

you are exactly right LM has model shop in Fort Worth with tons of models some of our flyers actually work in that department. So something fishy with this request as I know they have more funds...
Forum: AMA Discussions
11-19-2006, 10:57 AM
Replies: 76
Views: 7,276
Posted By cadmn

RE: I will never join AMA and why low #s joining

well I can tell you I belong to a great club here in Texas. they offer training by most of the seniors who provide plane, fuel, & advice Free!!!!!! they suggest Joining the A.M.A. for the fact of the...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.