RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 14
1
2
3
11
Last »
Search: Posts Made By: CurtD
Showing results 1 to 25 of 335
Search took 1.34 seconds.
Forum: Tips & Techniques
11-03-2018, 11:29 AM
Replies: 4
Views: 4,239
Posted By CurtD

Just as a side note on the SystemThree paint. I...

Just as a side note on the SystemThree paint. I use this paint exclusively for my models (it's the same as the old Nelson's Hobby paints). I did some testing and found that the cross-linker which you...
Forum: Tips & Techniques
10-11-2016, 06:08 PM
Replies: 8
Views: 3,524
Posted By CurtD

Haven't tried to use Minwax water-based...

Haven't tried to use Minwax water-based polycrylic directly on fabric covering over open structure but here is something you may want to consider... Koverall shrinks with heat but only so far....
Forum: Questions and Answers
12-29-2015, 07:43 AM
Replies: 31
Views: 5,319
Posted By CurtD

I've been thinning epoxy this way for years...

I've been thinning epoxy this way for years without a problem. When this happens, just put a heat lamp on it for a couple of hours and it will complete the curing. You don't want high heat, just...
Forum: Questions and Answers
12-29-2015, 07:31 AM
Replies: 23
Views: 2,230
Posted By CurtD

Just for future reference, the System 3...

Just for future reference, the System 3 (Nelson's) crosslinker also works with other water-based polyurethanes. I've tested it with Min-wax Polycrylic gloss and satin clear, and found it cures well...
Forum: Scratch Building, Aircraft Design, 3D/CAD
12-01-2015, 03:12 PM
Replies: 16
Views: 1,919
Posted By CurtD

For the best quality balsa I've found yet, I have...

For the best quality balsa I've found yet, I have to recommend http://www.specializedbalsa.com . I've ordered the light weight (6-8 lb stock) wood several times and have not been disappointed. The...
Forum: Scratch Building, Aircraft Design, 3D/CAD
06-18-2015, 09:53 AM
Replies: 3
Views: 687
Posted By CurtD

Putting the vertical fin and rudder in the front...

Putting the vertical fin and rudder in the front would make it unflyable. The vertical fin (properly "vertical stabilizer") must be behind the wing to do it's job which is to make the plane more...
Forum: Scratch Building, Aircraft Design, 3D/CAD
06-18-2015, 08:28 AM
Replies: 5
Views: 1,130
Posted By CurtD

Try Park Flyer Plastics. He has lots of canopies...

Try Park Flyer Plastics. He has lots of canopies for out of production kits.

http://parkflyerplastics.com/cart/
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
06-08-2015, 02:25 PM
Replies: 1
Views: 532
Posted By CurtD

I've tested my Maxima 9 with both Turnigy and...

I've tested my Maxima 9 with both Turnigy and Hyperion digital servos and they worked perfectly. I would expect that the Maxima works with any manufacturer's digital servos.
Forum: Classic RC Pattern Flying
12-05-2014, 04:23 AM
Replies: 22
Views: 6,014
Posted By CurtD

The ST MagV carb was one of the best carbs ever...

The ST MagV carb was one of the best carbs ever manufactured. At one time you could buy the carbs separately and with a little ingenuity fit them to other engines, usually anything with a Perry carb....
Forum: Tips & Techniques
07-16-2013, 11:02 AM
Replies: 9
Views: 1,420
Posted By CurtD

RE: sources for Nelson paint

...and mixed to match Monokote and Ultrakote which System 3 does not do. Their clear and cross-linker oughta work fine, tho'... ;)

Incidentally, their cross-linker will also work with...
Forum: RC Gliders, Sailplanes and Slope Soaring
07-16-2013, 10:48 AM
Replies: 8
Views: 1,212
Posted By CurtD

RE: A few questions about The Bird of Time

I agree with Bax. I've been flying a BOT built for electric power for about 2&1/2 years with no problems at all. The bit of spring tension provided by spreading the wires a little prevents any...
Forum: Questions and Answers
03-22-2013, 12:27 PM
Replies: 17
Views: 7,630
Posted By CurtD

RE: Need help with biplane ailerons

SIG makes a special biplane aileron connector horn that allows them to work properly together with one servo:

http://www.sigmfg.com/cgi-bin/dpsmart.exe/MainMenuFV5.html?E+Sig

It mounts at...
Forum: Questions and Answers
11-10-2012, 01:38 PM
Replies: 20
Views: 2,021
Posted By CurtD

RE: Warbird Colors and/or Nelson Paints

Just for reference...

System Three poly and Nelson's paint are the same thing. Nelson's custom blends the System Three for the Monokote, Ultracoat, and military matching colors that they offer...
Forum: Questions and Answers
03-26-2012, 05:01 PM
Replies: 2
Views: 883
Posted By CurtD

RE: Gimbal tension springs for JR 9303

I've replaced the springs at one time or another on pretty much every transmitter I've had including the latest Hitec Aurora 9. I've never done a 9303 but a JR 652 and several 8103's. It's not very...
Forum: Batteries & Chargers
09-25-2011, 07:51 AM
Replies: 3
Views: 1,241
Posted By CurtD

RE: LiFePo batteries

If it was me, I would cycle the batteries to determine what their capacity actually is. Even though they took a charge their capacity may be greatly diminished. You'd want to know this before putting...
Forum: Tips & Techniques
08-12-2011, 12:51 PM
Replies: 7
Views: 2,149
Posted By CurtD

RE: Midwest Push Pins Not a Bargain

I like Hobby Lobby's pins. That's the one in Nashville. Used them for years and never a problem:

http://www.hobby-lobby.com/pins.htm?pSearchQueryId=1710398

The ones I have are orange but...
Forum: Scratch Building, Aircraft Design, 3D/CAD
04-24-2011, 09:02 AM
Replies: 13
Views: 5,296
Posted By CurtD

RE: Drill press milling vice

I have one of these and have used it with success.

If you're looking for high accuracy, this isn't the way to go but general/light milling definitely can be done with it, using a good drill...
Forum: Gas Engines
02-16-2011, 12:49 PM
Replies: 443
Views: 70,024
Posted By CurtD

RE: MT 35 Looks Like a Winner

Not to hijack the thread but...

Take a look at Hyperion Atlas servos. They're also made in Korea and appear to be very high quality at reasonable prices. I'm running them in my pattern birds...
Forum: Golden Age, Vintage & Antique RC
01-13-2011, 02:47 PM
Replies: 21
Views: 4,064
Posted By CurtD

RE: Sealer for fabric

It's call "WR-LPU Topcoat". Here's the link:

http://www.systemthree.com/store/pc/WR-LPU-Topcoat-c29.htm

BTW, you'll need to order the cross-linker seperately if you buy the 4 oz bottles....
Forum: Golden Age, Vintage & Antique RC
01-12-2011, 12:08 PM
Replies: 21
Views: 4,064
Posted By CurtD

RE: Sealer for fabric

PolyC is not glow fuel proof. Even 0% nitro methanol-based fuel will cause it to soften. Nelson's Clear worked great as a fuel-proofer over PolyC when used with the cross-linker but sadly, Jerry has...
Forum: RC Gliders, Sailplanes and Slope Soaring
01-06-2011, 07:41 PM
Replies: 14
Views: 2,061
Posted By CurtD

RE: Radian & Monokote?

Before you spend too much time cutting the squares out, cut one square and try it. I've used Trim Monokote on my Radian but it does not stick very well to the foam and peels easily. I ended up using...
Forum: Composites Fabrication And Repair
01-02-2011, 12:18 PM
Replies: 6
Views: 6,481
Posted By CurtD

RE: Find Cheap Carbon Fiber rods

Check Hobby Lobby...

http://www.hobby-lobby.com/carbon_fiber_rods_strips_420_ctg.htm

Good selection of rods and tubes at excellent prices with free shipping if order over $50.
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
12-31-2010, 06:17 PM
Replies: 1
Views: 964
Posted By CurtD

Throttle lock switch odd behavior

I programmed switch D to activate the throttle lock feature on my Aurora 9 V1.07(2). It works properly except when I first turn the transmitter on and go into transmit mode, the throttle lock is not...
Forum: Questions and Answers
12-12-2010, 02:49 PM
Replies: 15
Views: 4,551
Posted By CurtD

RE: Solartex and Poly-Tak

Klasskote is nothing like Nelson's. Nelsons / System 3 is a water-based single part paint that has virtually no odor. only the primer is two-part. Klasskote is a two-part epoxy similar to the old K&B...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
11-26-2010, 08:51 PM
Replies: 2
Views: 1,210
Posted By CurtD

RE: Aurora 9 Firmware upgrade issue

Thanks for the quick response, Alan. That got it. A case of not RTFP on my part...
Showing results 1 to 25 of 335
 
Page 1 of 14
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.